Jump to content

Poljot 2415 barrel bridge not sitting flat


Recommended Posts

Working on a Poljot 2415 and have had various problems but help from WRT has enabled progress to be made. My latest problem is that the barrel bridge will not seat flat onto the main plate. When i remove the barrel and coupling clutch it seats fine, it also seats fine with only the barrel fitted. Its when both barrel and clutch are fitted that the bridge rocks and will not sit flat. I have had to source replacement barrel and clutch because the barrel 'pinged' away when i tried removing the mainspring and the clutch was in bits inside the watch.  Anyone have any ideas?

 

 

Link to comment
Share on other sites

It may not be any help to you but there is a full rebuild of a 2415 on my blog (link below in my signature).

The only thing that occurs to me is that the click may be resting on top of the ratchet wheel rather than against its rim, which would prevent the bridge from seating properly. The click needs to be held away from the ratchet wheel (against its spring) when fitting the bridge.

Link to comment
Share on other sites

@Myron62 I have just had a play around with a 2415 that I currently have in pieces to see if I can replicate the problem. Two possible causes come to mind.

1. If the reverser clutch isn't properly seated on the square of the M/S arbor then it will sit high and block the bridge from seating down properly. I don't think this is the case with yours though. Looking at mine, with the reverser clutch properly seated the space between the two reverser wheels is about the same as between the bottom reverser wheel and the barrel, and that looks to be the same as yours. This may be worth a check though.

2. If the barrel lid isn't properly seated on the barrel it may lift the whole assembly slightly out of the main plate. Fitting the bridge without the reverser clutch may still work as the length of the arbor doesn't change. However, if you try it with the clutch in place the increased height of the cluitch wheel above the main plate due to the less than fully seated barrel lid could cause the problem you have. So it might be worth checking that the barrel lid is fully seated.

I don't think that the fact that the barrel and clutch have been replaced should be problematic if they came from another 2415. The barrel arbor is clearly not the issue as everything works without the clutch installed. I does occur to me though looking at your pics that the cluth reverser wheels look slightly thicker than mine. On mine the clutch assembly is 0.90mm thick with no thickening at the hub. If yours is thicker than this or has a raised hub then this would cause a problem.

Glad you like the blog :biggrin:

ps. It's always the ones that are staring you in the face that are the most difficult to spot!!!

Edited by Marc
addition of ps
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Haha. You're just in a wicked mood today John 😅
    • Heres my watch of today, a Smith 13'" RY . My missus bought me this for this Valentines day a bargain 14.99 with a reduction, the seller has occasional 20% off offers now and then so it was about 15ish with delivery. I love Smiths and i love bulleye dials, this is my first one. The watch arrived non working as stated and i knew what was inside and what would be against me, but i enjoy a challenge, we dont expect a lot if anything from pin pallet movements. A balance pivot was broken and i didnt have another staff but i did have another RY with a battered dial so i robbed the balance and tweaked it around to make it work apart from that mostly just a good clean and relubrication. Keyless works are pretty rough by design and the crown is a bugger to get in and out with the dial on, the setting lever hits the dial before it releases it, so a little mod is needed to help that along. Major problem was the pins on the lever were quite worn which make the old tg have a snow storm fit. Its a similar read for most pin pallets, these were brass as was the escape wheel. But perseverance is me, i didn't change the pins but i did spend some time dressing and polishing the worn areas which improved the trace a lot with some straightish lines 😅 and a beat error of .5 . Not sure what the lift angle should be on these and i Wasn't in the mood to work it out and who believes timegraphers anyway, but at the default 52° it runs with 260ish full 210 after 24 hours dial down , the verticals rates were pretty much all over place. So lets just put it in it's superlight aluminium case and see what happens. Been wearing it now for 3 weeks and it's consistently losing around 1.5  minutes a week winding each morning i think pretty good for an old pin pallet watch. I just love this dial, thanks wifey heres my Valentine's gift for yer sweetie x
    • I have a PDF below that will help. The problem was the PDF wasn't designed for this purpose it was designed to tell you what size watch you  have. Then it doesn't take into account movements come conceivably in different thicknesses.   watch-ligne-size-chart.pdf
    • That would be something! Which brings me back to;  
    • you think you're going to sleep tonight you're not, you're going to ponder the question of what makes you think those of the right parts?  
×
×
  • Create New...