Jump to content
  • 0
JONICURN

Whats wrong with my Omega?

Question

10 answers to this question

Recommended Posts

  • 0

Potential problems.

1. Out of beat, could happen if the watch was dropped.

2. Mainspring not good.

3. Dirty.

4. Bent/damaged pivots or pivot jewels...

I would take it back to the person who serviced it if the service was done recently.

Good luck

Share this post


Link to post
Share on other sites
  • 0

Take it back to the person or establishment that serviced the watch. Agree with anilv's analysis + there are many other possible reasons too. The only way to detect the fault is for a close inspection of the movement. 

Share this post


Link to post
Share on other sites
  • 0

Dose it repeat stoping at same hands position( time)? You probably removed hands altogether. Eliminate hands one at a time.

When it stops, remove seconds hand only. if the fault has remained. remove the minute hand as well, if the fault remains, remove the hour hand.

Dirty or faulty center tube, bent seconds hand, worn out center hole, dial plate center hole drift, so on.

Share this post


Link to post
Share on other sites
  • 0
7 minutes ago, JONICURN said:

The hands weren't catching.  I'm going to clean and re lube the mainspring and barrel.  I will post results.   Thanks ya'll

A dirty MS doesn't make a watch stop. Escapement fault (in first place), and other faults do.
You can also get important clue looking at it on the timegrapher. 

Share this post


Link to post
Share on other sites
  • 0

You mentioned it was serviced.. Did you service it yourself?

If you're going to dive in, suggest you start by removing the balance.. inspect pivots and hairspring. Next put some power into the mainspring and see if the pallet fork locks/unlocks properly. It should 'snap' from one side to the other.

If that is fine then remove power from the mainspring and remove the pallet fork. Wind the barrel a bit and the train should wind down. Try to move the wheels, if it spins a few more times then your have to inspect the pivots and pivot jewels closely. On older watches I usually find barrel holes worn.

Good luck.

Anilv

Share this post


Link to post
Share on other sites
  • 0

I re cleaned and re greased the mainspring (moebius 8200).  I wanted to replace the mainspring but didn't have one handy and it didn't look tired so i used it.  The watch is back working fine now.  If this happens again, i will have to look into the balance also.  The timegrapher is giving me good numbers and lines.  Thanks all. 

Share this post


Link to post
Share on other sites
  • 0
On 6/12/2019 at 8:02 AM, jdm said:

A dirty MS doesn't make a watch stop. Escapement fault (in first place), and other faults do.
You can also get important clue looking at it on the timegrapher. 

What JDM says.

I seem to repeat this a lot, but: you are more likely to have issues at the faster end of the gear train (including the balance/escapement) as there is considerably less torque at this end. It's a common assumption of beginner that mainsprings should be a likely cause of stopping a watch. Unless they are broken or slipping, this is unlikely to be the case.

Share this post


Link to post
Share on other sites
  • 0
6 hours ago, rodabod said:

What JDM says.

I seem to repeat this a lot, but: you are more likely to have issues at the faster end of the gear train (including the balance/escapement) as there is considerably less torque at this end. It's a common assumption of beginner that mainsprings should be a likely cause of stopping a watch. Unless they are broken or slipping, this is unlikely to be the case.

Thanks, that makes a lot of sense.  I will check on that too. 

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Answer this question...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...

  • Recently Browsing

    No registered users viewing this page.

  • Topics

  • Posts

    • Lol that's the problem JohnHutchins....I do not want to have to take apart this watch just to replace a capacitor, especially with those annoying/fragile plastic gears. Not worth the effort for a $60 job. I feel like Citizen made it like this in order to force customers to send their watch in for a $200 service that takes 6 months (in which they will just rip the stem out and replace the entire movement). Shame. You might be right though, Pip, maybe there's been some sort of manufacturing flaw or unseated piece that is preventing the stem from coming out. Shit does happen.
    • Maybe you have a broken or unseated piece meaning the stem removal lever doesn’t move into position when you pull the stem out. Shit happens! Sent from my iPad using Tapatalk
    • A vintage Dundee lady tonight. I doubt if this is the smallest Timex watch ever made, but it is certainly fairly dinky. Serviced and polished, but the strap that was on it is done, and I have no 10mm straps, so I'll need to get one. I'm unsure of the age, if any of the experts know, do tell.  Other than a very light crop of green fungus on the strap pins (fresh pins fitted) and the dead strap it was fairly tidy and polished up rather nicely. It is managing a fairly respectable swing of 265 degrees and sitting slightly fast at +70 at the moment, so I'll let it settle overnight and finish it up tomorrow.
    • Seems like you are getting to the point where you have to make a decision - do I disassemble the watch completely in order to get the movement out of the case?   
    • Pip - yeah I've also taken a look at the diagram, but thats the assembly from the underside of the movement. And if you look at the dashes, the set lever ends up being set into a place farther up towards the center, which can't be reached from the dial side. This thing is a straight up anomaly.
×
×
  • Create New...