Jump to content

Baume et Mercier Hamilton Battery ?


Recommended Posts

Hi All - I own a Baume et Mercier Hamilton Quartz. It has not run in a while and I would like to replace the battery. It was purchased in the 1995 so there is no warranty. The only information I can find online is to send watch back to Baume et Mercier customer service. 

I am new to watch servicing world but I would think changing the battery of a quartz movement is not the same as servicing a Valjoux 7750. I could spend $45 and have it service by manufacturer but it would go against the reason why I joined this watch servicing community. 

Does anyone know what battery is needed and where I can purchase online ?

If there is a good reason why I should not change battery myself, I am open to discussion.

Thank you... AJ

 

Link to comment
Share on other sites

You might have to pop the back off, or otherwise open the case to get the battery. The movement is probably made by someone else, like ETA, for Baume. However, without the movement caliber number it'll be more of a guess, methinks.

Otherwise, if you can find the same model on the auction site, and the back is off to show prospective buyers, that might clue you in. Still not definite though. Good luck.

Link to comment
Share on other sites

On 6/7/2019 at 5:15 AM, ajdo said:

I will pop the hood of my Baume et Mercier Hamilton this coming weekend and see what I can find a reference number on battery. 

Even without a battery at all you can identify it by the mov.t, or by  the size of the slot using the table attached.

ScoSu_Consumer_renata.pdf

Link to comment
Share on other sites

I tried to open B&M Hampton (purchased in early 90s) case but was unsuccessful and do not want to scratch it.

I think it’s time to start investing in better tools! 

I used one of those red knife-like that comes in a basic watch tool set but was unable to open the back of B&M Hamilton :( Tried the same tool on another inexpensive quartz watch I own and had the same issue, the “knife” just slipped off. 

I think I need some type of lever type tools which I suppose would make it easier. It could also be that I do not have the proper technic. 

If someone can shime-in on the proper tool I should get that would be great.

I guess it’s the biginning of a tools buying spree :) I will not work on my nice watches but my new found goal is to take appart, lube and put back together a Seagull 2824 I found in a clone Rolex I have. 

A tool list would be welcome. I am more middle of the road person, I do not like cheap tools but would not spend big $$$ on an activity I do not know will actually become a hobby. It’s really out of intereest for now but do not want to end up like Charlie Chaplin in Clock Repair short movie :)) 

Edited by ajdo
Watch model mistake
Link to comment
Share on other sites

52 minutes ago, ajdo said:

 

I used one of those red knife-like that comes in a basic watch tool set but was unable to open the back of B&M Hamilton :( Tried the same tool on another inexpensive quartz watch I own and had the same issue, the “knife” just slipped off. 

As often asked, tight snap on case backs are opened by first going around slowly and carefully with a blade like an exacto knife. After is lifted enough theb use a case back knife, Japanese types are good, pry around don't twist it. 

These subjects are well covered in the forum, just browse around. 

Link to comment
Share on other sites

Since you mentioned better tools.

https://www.aliexpress.com/item/New-Watch-repair-tool-Heavy-Metal-Made-Adjustable-Watch-Case-Snap-Back-Opener-professional-removal/32344173972.htm

With tips for bracelets, $10 more
https://www.aliexpress.com/item/New-Watch-repair-tool-Heavy-Metal-Made-Adjustable-Watch-Case-Snap-Back-Opener-professional-removal/32344173972.html

You also need a small press to close the back. But unless you do a lot of snap back, they are totally an overkill. Much more needed is good screw-in opener.

 

  • Like 1
Link to comment
Share on other sites



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • This set lever seems to working ok unhardened Nickelsilver, might it deform if i leave it that way ?
    • I found this from a while back CS100 seems fine, but at around 500 Vickers it's not quite as hard as "blue" steel, but still harder than annealed. I'd try to find annealed (the post above has a U.K. supplier of small quantities).
    • As an experiment i was thinking of not hardening it to see how it fairs. Now that i have a complete template i could knock up another in half the time if this loses its elasticity. I might play about with a few pieces today to test their bending and spring properties. This was cs 100 the supplier quoted in annealed state, it was nice to work with files so I'm taking it thats its state. What you are looking seems like it would need annealing to work it. This is why i went for this stuff that cuts out that process, it was so easy to work.
    • Showing state of hairspring on receipt, backplate & 'dished' wheel.  Thanks, Nev. Amplitude v. weak - balance wheel turns over arc of only ~20deg. Don't know how to calculate movement rate or safely vibrate balance spring! Meantime I have reduced the 'dishing' & clock no longer runs for more than a few minutes except face down which supports my theory that it was 'dished' as a hack to avoid doing a proper repair.
    • I would harden and temper (to a light blue). It's so easy to do and only takes a couple of minutes. A search on ebay UK for "spring steel strip cs" finds plenty available in small quantites and thicknesses from 0.1mm up.  But the question is ( @nickelsilver) which "CS" number is best for watch parts ?  Also, from one of the ads : "CARBON SPRING STEEL. SIZE IS METRIC 15.00mm X 0.10mm X 304 MM  CS100 FINISH BRIGHT . HARDENED AND TEMPERD TO 480-530VPN" I've no idea about 480-530VPN. Does that mean it needs annealing before working?       Have you seen this video, he shows how to determine where the indents go ?  
×
×
  • Create New...