Jump to content

SKX007 build


Recommended Posts

I'm a big fan of Seiko dive watches, I have a SSC017 and recently bought this case off ebay. I've checked out a few vids on youtube about modding this watch and being a newb, wanted some input on the movement type to put into it. I've heard some people say NH35/36 and wanted to know if I bought this mvmt new if it would have the mvmt spacer and come complete with day/date rings or for that matter if any other mvmts would fit.  Thanks for any and all info.

IMG_20190529_171230.jpg

Link to comment
Share on other sites

The original movement is the 7s26 which can be found some places online, but is not that easily available. NH36, which is day-date (NH35 is date only), is available from CousinsUK or for a similar price on Ebay/AliExpress. You have to switch out the day wheel to one that is for a 4 o'clock movement, as 99% of the NH36 movements you find online come with a 3 o'clock day wheel. The supplied grey spacer ring which is already mounted on the movement does fit in most cases, but there's a tiny chance that it'll be a bit too snug as it's a bit bigger in diameter than the black spacer, which is found on the 7s26.

So, NH36 is a day/date movement that you can use, but you have to get some 4 o'clock day wheels.

Link to comment
Share on other sites

14 hours ago, Leitemods said:

The supplied grey spacer ring which is already mounted on the movement does fit in most cases, but there's a tiny chance that it'll be a bit too snug as it's a bit bigger in diameter than the black spacer, which is found on the 7s26.

So, NH36 is a day/date movement that you can use, but you have to get some 4 o'clock day wheels.

Actually the holder rings are of the same diameter, but the diver version is slightly taller and will make proper contact with the caseback. Refer to page 8 of the attached technical guide.
And, you have not mentioned the most important parts, that is one will need a new crown because the windable mov.s the stem is different.
Some people like to buy an original Seiko crown/stem combo typically from a SARB for around $50, others including myself do just fine with one from the known Ebay sellers.

7S26C_36C.pdf

Link to comment
Share on other sites

3 hours ago, jdm said:

Actually the holder rings are of the same diameter, but the diver version is slightly taller and will make proper contact with the caseback. Refer to page 8 of the attached technical guide.
 And, you have not mentioned the most important parts, that is one will need a new crown because the windable mov.s the stem is different.
 Some people like to buy an original Seiko crown/stem combo typically from a SARB for around $50, others including myself do just fine with one from the known Ebay sellers.

7S26C_36C.pdf 2.84 MB · 0 downloads

good info, thanks for the correction! I just saw the technical guide that I found on NH25 VS 35 and saw a .1mm difference in casing diameter while the height was identical. Do you know how much the difference in height is, between the diver/non-diver?

 

And yes, I forgot the crown and stem... The SARB059 crown is commonly used, but usually more expensive and harder to find than aftermarket options. That one works without any modifications on the SKX. Crystaltimes, DLW Watches, Watch&Style, SeikoCrown and probably some more supply aftermarket crowns which will fit the stem that is supplied with the NH36 movement. It's possible to use the stem that's threaded on the plastic crown without trimming it, as that one already has the right length that is required for the SKX. I've personally chosen the pre-cut stem/crown combo from Crystaltimes, when I've swapped to the NH36.

Link to comment
Share on other sites

4 hours ago, GregC said:

Would the 7s,26 from a Seiko 5 work in the skx case?

Yes with very same 3 specific parts needed as mentioned above. 

Seiko 5 generally have stem at 3, thinner holder ring, and push type crown. 

Link to comment
Share on other sites

  • 1 month later...

I finally got around to getting the NH36 movement and changed out the day wheel. When I put on the dial and was turning the crown to establish the 12 o'clock position to install the hands, I noticed that no matter how much I turned the crown, it would not change over. Did I screw up something? I was turning clockwise like my other 7S26 Seiko. 

Link to comment
Share on other sites

On 5/31/2019 at 4:01 PM, GregC said:

The one I have here has the stem at 4 and date at 3. Any idea where I could get a ring to fit?

For what it's worth:  I replaced the movement in an SRP-775 (re-issue turtle) with one of the $36 NH36's from Ebay.  Put my day wheel and ring on it and it worked fine.  This watch has crown at 4.

The movement is impossible to regulate well.  I wonder if anyone else has had issues with the replacement movements.

Link to comment
Share on other sites

6 hours ago, nichod said:

The movement is impossible to regulate well.  I wonder if anyone else has had issues with the replacement movements.

NH36 are good mov'ts and should be accurate to the specifications or better. You can post pictures on the timegrapher (or equivalent application) take in 2 or 3 positions.

Link to comment
Share on other sites

 

9 hours ago, GregC said:

When I put on the dial and was turning the crown to establish the 12 o'clock position to install the hands, I noticed that no matter how much I turned the crown, it would not change over. Did I screw up something? I was turning clockwise like my other 7S26 Seiko. 

Do the day change? With the dial removed check that the day / date  driving wheel turns, that date ring is free and its finger spring is engaged. You will need to remove the calendar plate to correct any problem in this area. At the same time check quick-set. Attached service sheet.

 

7S26C_36C.pdf

Link to comment
Share on other sites

10 hours ago, jdm said:

NH36 are good mov'ts and should be accurate to the specifications or better. You can post pictures on the timegrapher (or equivalent application) take in 2 or 3 positions.

I just got a new Timegrapher 1900 out of the box a few minutes ago.  It looks to be about the same as the Watch-O-Scope I been using as far as the readings.   My beat error is way high at about 2.5 MS.   I can get it down to about 1.1 or so and then it goes the other way.  I'll try again on the new machine and report back.    Perhaps I should have opened a new thread.....

Link to comment
Share on other sites

11 minutes ago, nichod said:

I just got a new Timegrapher 1900 out of the box a few minutes ago.  It looks to be about the same as the Watch-O-Scope I been using as far as the readings.   My beat error is way high at about 2.5 MS.   I can get it down to about 1.1 or so and then it goes the other way.  I'll try again on the new machine and report back.    Perhaps I should have opened a new thread.....

You should be able to bring  Beat Error to under 0.5 ms with careful tiny motions. But what matters more that BE is amplitude and pattern regularity. You can also expect a position error of 30 sec/d day between some positions, which may (or may not) be reduced turning the Etachron regulator. All that is in the service manual and discussed many time on this forum 

Link to comment
Share on other sites

Ok, I took off the day wheel and replaced it with another which does the same thing. It makes an attempt to change and goes plix and stays on the same day. I put the original wheel it came with and it does the same thing. What am I doing wrong? The only thing that moves is the black wheel between 10 and 11 o'clock. 

 

IMG_20190721_183023.jpg

Link to comment
Share on other sites

9 hours ago, GregC said:

Ok, I took off the day wheel and replaced it with another which does the same thing. It makes an attempt to change and goes plix and stays on the same day. I put the original wheel it came with and it does the same thing. What am I doing wrong? The only thing that moves is the black wheel between 10 and 11 o'clock. 

Does that with both time advance and quick setting (white plastic wheel, dot up)? Check that the finger spring engages, normally it does as soon the wheel is turned. When it doesn't, the wheel remains raised above it.

The black (day/date) wheel should be turning all the time. Of course the fingers engage only every 24h.

For a refresh is always good to watch, subscribe, and why not take the course by our Host Mark Lovick. 

 

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • that band is old as stated, there is a kit that pops up from time to time on selling sites for the repair of these type bands, some of this type are adjustable on a few links, one adjustable type allows you to align the round opening in the expansion slit [like yours] with the rivet to separate, but if yours won't come out then the rivet head is too big and will have to be done with some rivet removal and replacement, I suppose if you could make/optain the correct rivets that one could alter the said band, the tops/caps do lift off after raising the tabs....  
    • This is a watch from a friend who sent it to a neighborhood watchmaker for a battery change. It came back with the watch stem in a ziplock bag and the dial skewed 20°. The watchmaker told him that the stem was faulty and the watch cannot be repaired. I opened up the watch and found that one dial foot was broken off and still stuck in the movement, while the other was bent until it was flat against the dial. The stem could be inserted but it couldn't be pulled out to quickset and time adjusting positions. I did a full disassemble, cleaned and oiled the movement. But when it put in the battery, the second hand runs super fast. Like it gains 30 mins every hour. Any advice on fixing this problem? TIA.
    • I determined that the balance staff is rotating, not the roller table, so my second attempt at riveting was unsuccessful. I have ordered a new balance staff and will take measurements when it arrives. The balance staff i originally ordered (and now reordered) was specified as: Replacement balance staff: (A. Schild Caliber 984 1002 1021 1124 Original Balance Staff Part 723) so it should be correct. Measurements: (see pic below for terminology) xxxyy is a place holder until the new balance staff arrives. Lower pivot: Old - .08 mm New - xxxyy Lower pivot to balance seat: Old - 1.53 mm New - xxxyy Roller shoulder: Old - .42 mm New - xxxyy Hub: Old - xxxyy New - xxxyy Balance shoulder: Old - .86 mm New - xxxyy Collet shoulder: Old - .56 mm New - xxxyy Upper pivot: Old - broken New - xxxyy
    • Hello and welcome from Leeds.  We're here to help. 
    • I was just about to adk that, probably they have unnecessary waiting lists to make their watches appear more exclusive than they actually are.
×
×
  • Create New...