Jump to content

Omega Geneve 1970’s automatic watch stopped working after popping off the glass


Recommended Posts

I was following this video to pop out the glass on my Geneva watch.

 

I wanted to pop out the glass to adjust the calendar frame. However, after popping out the glass,  the automatic watch stopped working. Could it be possible that the pressure of air from the syringe damage something? I appreciate if anyone can suggest possible problems. Below is my watch.

Thank you in advance.

 

 

20CCEAF0-1CF1-456A-A71D-4064D7024DE9.jpeg

84CB9840-FBD7-48E7-9299-45CBC3B4DC5D.jpeg

Link to comment
Share on other sites

My guess is that the dial lifted slightly and this has taken the pressure off the dial washer underneath, allowing things to get loose and the hands to stop turning. However this is only a guess.  Proceed with caution. Check to see if the dial feet screws are loose. Check to see if you can move the hands with the crown.

  • Like 1
Link to comment
Share on other sites

Call me paranoid but I would not use the air blowing method on any watch (unless it had no small moving parts but what watch has that, right?).

I'd rather just use the claw tool to remove teh crystal.

Link to comment
Share on other sites

32 minutes ago, Chopin said:

Call me paranoid but I would not use the air blowing method on any watch (unless it had no small moving parts but what watch has that, right?). I'd rather just use the claw tool to remove teh crystal.

Some crystals, like the one that is in the video and owned by the OP have absolutely no lip to grab with a lifter. So there is no other choice. Remember that our Mark is not in the business of teaching how to damage watches, but exactly the opposite.

  • Like 1
Link to comment
Share on other sites

You could try the carpet tape trick with that type of glass. It is not without its hazards mind you. I can see there is a potential to launch the watch and/or the crystal in to orbit, or end up with insanely sticky goop in places it really aught not to be, but I suspect it would work.

Link to comment
Share on other sites

4 hours ago, AndyHull said:

You could try the carpet tape trick with that type of glass.

There are also suction cups specially made for this. I've never seen a report about their effectiveness.

Link to comment
Share on other sites



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • OK, welcome in the world of alarm clocks... I guess the 4th wheel is dished because it is from another movement. If it was not dishet, then it would not mesh with the pinion of the escape wheel, am I right? The marks of wear on the 4th wheel pinion doesn't corespond to the 3th wheel table position, at list this is what i see on the picts. Calculating the rate is easy - there is a formula - BR = T2 x T3 x T4 x T5 x 2 /(P3 x P4 x P5) where T2 - T5 are the counts of the teeth of the wheels tables, and P3 - P5 are the counts of the pinion leaves. Vibrating the balance is easy - grasp for the hairspring where it should stay in the regulator with tweasers, let the balance hang on the hairspring while the downside staff tip rests on glass surface. Then make the balance oscillate and use timer to measure the time for let say 50 oscillations, or count the oscillations for let say 30 seconds. You must do the free oscillations test to check the balance staff tips and the cone cup bearings for wear. This kind of staffs wear and need resharpening to restore the normal function of the balance.
    • Glue a nut to the barrel lid, insert a bolt, pull, disolve the glue.  Maybe someone will have a better answer. 
    • The stress is the force (on the spring) x distance. The maximum stress is at the bottom, and decreases up the arm. That's why they always break at the bottom. I used a round file, then something like 2000 grit to finish. I gave the rest of the arm a quick polish - no need for a perfect finish. Just make sure there are no 'notches' left from cutting/filing. The notches act like the perforations in your toilet paper 🤣
    • It's probably a cardinal rule for watch repair to never get distracted while at the bench. Yesterday, after finishing a tricky mainspring winding/barrel insertion (I didn't have a winder and arbor that fit very well) I mentally shifted down a gear once that hurdle was passed. There were other things going on in the room as I put the barrel and cover into the barrel closer and pressed to get that satisfying snap. But when I took it out I realized I never placed the arbor.  When opening a barrel, we are relying on the arbor to transfer a concentrically-distributed force right where it is needed at the internal center of the lid. However, when that isn't present it's difficult to apply pressure or get leverage considering the recessed position of the lid, the small holes in the barrel and the presence of the mainspring coils. It was a beat-up practice movement so I didn't take a lot of time to think it over and I pushed it out using a short right-angle dental probe placed in from the bottom, but that did leave a bit of a scratch and crease in the thin lid. I had also thought about pulling it using a course-threaded screw with a minor thread diameter smaller than the lid hole and a major diameter larger, but that may have done some damage as well.  Thinking about how this might have been handled had it been a more valuable movement, is there a method using watchmaking or other tools that should extract the lid with the least damage? 
    • 🤔 what happens if lubrication is placed directly on top of epilame ? Making a small groove so the lubrication doesn't spread across the component but what if when lubing a little overspills and sits on the epilame .
×
×
  • Create New...