Jump to content

Omega Geneve 1970’s automatic watch stopped working after popping off the glass


Recommended Posts

I was following this video to pop out the glass on my Geneva watch.

 

I wanted to pop out the glass to adjust the calendar frame. However, after popping out the glass,  the automatic watch stopped working. Could it be possible that the pressure of air from the syringe damage something? I appreciate if anyone can suggest possible problems. Below is my watch.

Thank you in advance.

 

 

20CCEAF0-1CF1-456A-A71D-4064D7024DE9.jpeg

84CB9840-FBD7-48E7-9299-45CBC3B4DC5D.jpeg

Link to comment
Share on other sites

My guess is that the dial lifted slightly and this has taken the pressure off the dial washer underneath, allowing things to get loose and the hands to stop turning. However this is only a guess.  Proceed with caution. Check to see if the dial feet screws are loose. Check to see if you can move the hands with the crown.

  • Like 1
Link to comment
Share on other sites

Call me paranoid but I would not use the air blowing method on any watch (unless it had no small moving parts but what watch has that, right?).

I'd rather just use the claw tool to remove teh crystal.

Link to comment
Share on other sites

32 minutes ago, Chopin said:

Call me paranoid but I would not use the air blowing method on any watch (unless it had no small moving parts but what watch has that, right?). I'd rather just use the claw tool to remove teh crystal.

Some crystals, like the one that is in the video and owned by the OP have absolutely no lip to grab with a lifter. So there is no other choice. Remember that our Mark is not in the business of teaching how to damage watches, but exactly the opposite.

  • Like 1
Link to comment
Share on other sites

You could try the carpet tape trick with that type of glass. It is not without its hazards mind you. I can see there is a potential to launch the watch and/or the crystal in to orbit, or end up with insanely sticky goop in places it really aught not to be, but I suspect it would work.

Link to comment
Share on other sites

4 hours ago, AndyHull said:

You could try the carpet tape trick with that type of glass.

There are also suction cups specially made for this. I've never seen a report about their effectiveness.

Link to comment
Share on other sites



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Welcome my friend. 
    • Been there. Worn that Tshirt.  'ping'. Hands and knees. Nothing. Nada. 20 minutes? Ha! I found it 7 month later. How? Well, after advice from a member, I invested in a £4 UV light torch.  Hands and knees looking for a 'ping' from a Sekonda, found them both within 30 seconds. UV makes the jewel shine. easy peasy. Could have taken longer. Just lucky on the location of the search. Hope this helps.
    • Thanks Dell. I thought about silver soldering. Have never done it but would like to give it a go. Do you think to put flux on the butted joint then run the solder in or to maybe brace it with a piece of scrap spring steel?
    • Never and others. Yes, like you I do spend a fair amount of time reading the contents of this forum. I find it better that any other. Clear, lucid, no Prima Donas, and most of all an easy access without adverts. All thanks to Mark. God bless you mate. You give so much to many of us. What if? No Mark? Hypothetically. A forum. I did run a forum for a few years. Really enjoyed it, but became so engrossed that it did affect my health. I gave to to others to run. Not been back. It was very successful and rivalled a number of large paying sites. No adverts, no others but me. I did ask and listen to members comments and it worked well.    Costs Having a domain name, £10 annually.  Register the site with a forum company, free. Build the site using the forum company guide lines, free. It looked and ran almost the same a Mark's. All the same facilities. The cost was only £5 per month, but counted visits (views). If I recall, it was that price for 5,000 views. Each extra 5,000 views increased the price by £2 per month. Success was my own personal undoing. From £5 per month initially, it rose to £60 a month and looked like increasing. This was 10 years ago. I could not afford that, and asked it anyone would like to take over and someone did. I would assume that this is the price that Mark is funding for us all. His return is our continued comments on the internet about his course, and the fact that many of the big names on YouTube mention him as their Tutor. Those of us who have done, and are still using, his course, benefit. In comparison to other courses, I can't believe how cheap it is, and the value is exceptional. It is the structure that gives the value. Long may Mark reign. Ross  
    • Hi all, total newbie to watchmaking and I've had a bit of a mishap. Just completing level 2 and was doing ok, but I was just on the last part of the reassembly of my ST3620 when the balance end stone shot across the room, just as I was trying to see if I had put the correct amount of oil between it and the balance end, aarrrgh! Been on my hands and knees combing the carpet for 20mins looking for it but to no avail. Does anybody know where I can get a replacement from and what to look for please?? Thanks.
×
×
  • Create New...