Jump to content

Anyone familiar with Citizen 52**/54**/64** cals, as this one has me stumped?

mikepilk
 Share

Recommended Posts

mikepilk Distinguished Member

mikepilk

Posted
Posted

I've been trying on and off for months to get reasonable amplitude from a 33J Citizen Cal 5204. 

The gear train runs as freely as any watch I've cleaned, and the balance swings freely, no rubbing. 

I've inspected all jewels/pivots under the microscope, oiled as per Technical Guide.
Fitted new mainspring and balance (end-shake OK).  There are no cracked or loose jewels. Demagnetised

And yet I couldn't get above 180 - 200 deg amplitude, despite stripping, re-cleaning, re-examining all the parts (several times)

I never give up (though I might have to on this) . So I looked for another movement to start swapping parts.
 After weeks of searching I eventually found another cal 5204 movement (not common!)

The hole at the bottom of the barrel was worn, but the movement looked very good. 

So I cleaned/inspected/oiled this one, used the better barrel with the new mainspring from the first movement.

The gear train was beautifully free, the balance swung nicely, all was looking great ......... and I get 190 deg amplitude!

I just can't see where the problem is. Does anyone have experience of these models, who could suggest some ideas ?

This could be the first one to beat me :thumbsd:

 

WIN_20190202_12_54_45_Pro.jpg

s-l1600 (1).jpg

WIN_20190212_13_42_05_Pro.jpg

WIN_20190212_13_41_57_Pro.jpg

Link to comment
Share on other sites
rogart63 Distinguished Member

rogart63

Posted
Posted (edited)

Have the same problem. Think it was a 5470 . Can't figure out the problem. Not sure about the lift angle. Did you try to set it to 46 degree.  If so how did that affect the amplitud?

Edited by rogart63
Link to comment
Share on other sites
mikepilk Distinguished Member

mikepilk

Posted
  • Author
Posted
41 minutes ago, rogart63 said:

Have the same problem. Think it was a 5470 . Can't figure out the problem. Not sure about the lift angle. Did you try to set it to 46 degree.  If so how did that affect the amplitud?

So I'm not the only one! 

Unfortunately setting 46 degrees makes it worse. I wasn't sure the timegrapher was correct so I put a mark on the balance, and it agreed. 

Link to comment
Share on other sites
rogart63 Distinguished Member

rogart63

Posted
Posted (edited)

Have a watch that i am going to service in the near future. I hope i can get it to run okay. Need a new balance for it as the hairspring is badly damaged. The wheel train  is running smooth so hopefully it will be fine. 

The other i did that i couldn't get to work is now spare parts :) . The owner didn't want to pay as much for it . I found out the hairspring stud was damaged . So that also needed a balance. But there was other things wrong with it to. 

One thing that i wonder about is the double wheel . That has two wheels on one axle . Only  of  gears are is in contact with an other wheels gear.  

Edited by rogart63
Link to comment
Share on other sites
mikepilk Distinguished Member

mikepilk

Posted
  • Author
Posted
24 minutes ago, rogart63 said:

Have a watch that i am going to service in the near future. I hope i can get it to run okay. Need a new balance for it as the hairspring is badly damaged. The wheel train  is running smooth so hopefully it will be fine. 

The other i did that i couldn't get to work is now spare parts :) . The owner didn't want to pay as much for it . I found out the hairspring stud was damaged . So that also needed a balance. But there was other things wrong with it to. 

One thing that i wonder about is the double wheel . That has two wheels on one axle . Only  of  gears are is in contact with an other wheels gear.  

I can't figure out that double wheel. It looks like both wheels mesh with the sweep second pinion! 

I managed to get a new balance quite cheaply. The problem was finding the part number. 

Have a look here, basically the same movement and good amplitude 

https://mitka.co.uk/2019/05/20/service-citizen-150m-diver-68-5372/#more-12743

  • Like 1
Link to comment
Share on other sites
rogart63 Distinguished Member

rogart63

Posted
Posted
4 hours ago, mikepilk said:

I can't figure out that double wheel. It looks like both wheels mesh with the sweep second pinion! 

I managed to get a new balance quite cheaply. The problem was finding the part number. 

Have a look here, basically the same movement and good amplitude 

https://mitka.co.uk/2019/05/20/service-citizen-150m-diver-68-5372/#more-12743

Have one of those here also in parts. Have serviced a couple of those and they are running good with great amp. Think it was 270 -280 . Don't know why the 5470 is running so bad.  If it's the 21600 Hz instead of the 5470 18000 hz  

  • Like 1
Link to comment
Share on other sites
mikepilk Distinguished Member

mikepilk

Posted
  • Author
Posted

I think the problem could be play in the barrel arbor. One barrel had holes which were badly worn.
Even with the one that seemed OK,  I can tilt the barrel a bit when it's installed. With it on the timegrapher I can get the amplitude going from about 190 to 220 deg by tilting the edge of the barrel with some pegwood. I think that's a clue !  

The power does go through the sweep second pinion (seems odd) - which takes it from the bottom third wheel to the top one.

So it's worth checking that the sweep second pinion is fitting ok, and oiled.

 

image.png.437037172971b098a415ceb34cc516ae.png

  • Like 1
Link to comment
Share on other sites
saswatch88 WRT Addict

saswatch88

Posted
Posted
On 5/21/2019 at 6:48 AM, mikepilk said:

I can't figure out that double wheel. It looks like both wheels mesh with the sweep second pinion! 

I managed to get a new balance quite cheaply. The problem was finding the part number. 

Have a look here, basically the same movement and good amplitude 

https://mitka.co.uk/2019/05/20/service-citizen-150m-diver-68-5372/#more-12743

Citizens dont always yield the best amplitudes but none the less 180-200 is still too low - if both movements were serviced with no broken jewels or excess wear and they both dont have good amp then like any experiment we have to see what was the constant here. The barrel and mainspring right, so an educated guess would say there lies your problem. This is the beauty of having two movements to work with. I know you posted on this before about ordering a new mainspring and barrel, and if i recall the one that was pulled was a stronger strength than the OEM one. Then there was an issue with breaking grease, correct me if iam wrong here.

I would say this: It was very common for old watchmakers to replace mainsprings with one that had a higher strength to account for amplitude issues due to wear, i work on old pocket watches and you will find that there are mainsprings designed for the same movement with usually 3-4 different strengths available from the factory. When I service a 50-100 year old movement i replace it with a mainspring that is at least 2/100th stronger than what was in there originally. try that, if that dont work then my next guess would be the hairspring, they too wear down and loose strength over the years, but a stronger MS should help with that as well but how much in your case i wouldnt know.

Link to comment
Share on other sites
mikepilk Distinguished Member

mikepilk

Posted
  • Author
Posted

I did put in a slightly stronger mainspring, and yes, I did post about breaking grease. In confident its now winding enough before slipping. 

There are some new barrels on sale but I can't find the part number. If anyone has a parts list? 

I also fitted a new balance, so it's not the hairspring 

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • ManSkirtBrew
      1972 Bulova President "E" Sea King 11ACACB movement

      By ManSkirtBrew · Posted

      Unfortunately I'm not that lucky. I started on the train side and after I noticed the binding I pulled everything out except the driving wheel to rule everything else out. It still binds. I'm going to double check that the pinion is fully seated on the staff first, then if no joy I'll push the bridge jewel up a fraction of a mm. Fingers crossed!
    • Waggy
      Rado rotor removal

      By Waggy · Posted

      Happy to have helped, great way to start the day with a win! 🥳
    • doober
      Rado rotor removal

      By doober · Posted

      Thank you for the advise!! It worked. The setting screw was a lock/unlock to remove the rotor. 
    • GuyMontag
      1972 Bulova President "E" Sea King 11ACACB movement

      By GuyMontag · Posted

      I have that French tech sheet too, it is a little different than the English one (eg, it doesn't have the auto works diagram). BTW, it looks like you are looking up the case number in the 1979 ABC supplement. The 1974 ABC catalog does have the 3093 case. As you determined it takes the 1222-5 crystal.  When I serviced my President 'A' (which also takes that crystal), I was able to fit a 29.8 crystal from my DPA crystal assortment. Those are, in my opinion, a great deal. The assortment comes with 10 sizes each from 27.8mm to 32.4mm in 0.2 increments. I pretty much use them for any non-armored crystal that takes a high dome crystal. I think they no longer make them but Cousins has still has some in stock but when I bought them they were around $40 for the set and now they are around $100. Still, at 40 cents a crystal it's still a good deal. For the large driving wheel, I remember I once assembled the keyless/motion works first and when I placed the large driving wheel it was interfering with the setting wheel on the dial side as the teeth were not fully meshing and it wouldn't fully seat. If that isn't the issue I got nothing and am looking forward to see how you solve it 🙂
    • Waggy
      Rado rotor removal

      By Waggy · Posted

      Not sure, but just looking at it, it seems like the screw on the right may be a fake? The one on the left may not be a screw in the regular sense at all, rather a 2 position device, I think you need to point the slot towards either of the 2 dots and one will secure and one will open. Like I said this is just my best guess looking at the pictures.
×
×
  • Create New...