Jump to content

How to remove stem on Certina 29-252 Quartz

Chopin

By Chopin
in Watch Repairs Help & Advice

 Share

Recommended Posts

Chopin Super WRT Addict

Chopin

Posted
Posted

Could someone tell me how I can remove the stem from such a watch ? I believe it's a rebrand of an ESA 9181.

I can see a fairly large screw in the stem area but I'm not sure if it's that one. There is a two-sided arrow near it as well.

Also, I should pull the crown all the way out before attempting to unscrew anything, right ?

Generic pic off the internet.

certina-eta-29-252-268546-c59b17ab.jpg

Link to comment
Share on other sites
MrRoundel Super WRT Addict

MrRoundel

Posted
Posted

Since your image is hosted at an outside service, I can't magnify the image, at least without signing up for their service or something.

Based on what I might be seeing, I'd press that copper colored spot, to the right and down from the crown maybe 8mm or so, and pull on the crown. However, if pressing the spot doesn't look for feel springy, I wouldn't force it. I just can't see it clearly enough. Good luck.

 

Link to comment
Share on other sites
Chopin Super WRT Addict

Chopin

Posted
  • Author
Posted

The part that you pointed the arrow at actually moves as you pull or push the crown so that's why I fear it might not be what needs to be pushed. Will try to check tomorrow.

I did think of that hole but I can't see much inside...

Link to comment
Share on other sites
jdm Distinguished Member

jdm

Posted
Posted
12 minutes ago, Chopin said:

The part that you pointed the arrow at actually moves as you pull or push the crown so that's why I fear it might not be what needs to be pushed.

That's exactly the indication of that being the setting lever you need to push.  

Link to comment
Share on other sites
Lwayslate Member

Lwayslate

Posted
Posted

I have found that many ETA calibres have no release button but the screw beside the stem needs to be loosened a turn or so...but just until the stem is released. I suggest being very careful of pushing on anything if there's no embossed arrow pointing at it...the electronic circuits are easy to damage.

Sent from my BBF100-2 using Tapatalk

  • Thanks 1
Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • RichardHarris123
      Landeron 248 setting eccentric studs

      By RichardHarris123 · Posted

      It opened today, excellent as usual. 
    • nevenbekriev
      Pocket watch escape wh

      By nevenbekriev · Posted

      I will advice to share the idea first here before doeing something to the movement
    • Jon
      Omega cal. 565 - low amplitude

      By Jon · Posted

      When you move the index which changes the timing from an extreme fast to an extreme slow, is there a big change in beat error? Obviously there will be a big change in timing. If there is a big difference in BE then this is strongly inferring the the end-curve of the hairspring isn't set correctly or/and the collet is central to the jewel on the balance cock, because the hairspring that is breathing between the curb pin and boot is being pushed and/or pulled when you move the index from left to right. Also not having the hairspring set correctly can dramatically reduce the amplitude. A quick check is to take power off the movement and move the index from extreme fast to slow and with high magnification see if the hairspring sits nicely between the curb pin and boot at all times (give the balance a spin and watch the hairspring - has it got total freedom?) or if it moves by being pushed or pulled by the curb pin or boot. I'm guessing it is the latter. I think that may be a possibility to your problem.
    • RichardHarris123
      Unbranded skeleton movement

      By RichardHarris123 · Posted

      I can't get windingstens.com to open but you need a  few measurements. 
    • Waggy
      Movement holder made with 3D printer

      By Waggy · Posted

      All Done, Here are the finished pictures: This one shows the generic "one-size-fits-all" base which accepts the bespoke rings - notice that the parametric movement OD (27.40 mm) automatically prints on the ring 🙂 From another angle: Here is the ring about to go into the base: And finally the base and ring together: Here it is next to a pen for scale: On my system with 20% fill each ring will take about 18 mins to print, but I am sure this could be optimised: Here is the screenshot of the spreadsheet in FreeCAD, you just need to change one value to create the ring in cell C3, (the base doesn't need any changes). I just uploaded the files to printables link here, but also include  here as a fake pdf, please change the .pdf to .zip to make the file work once downloaded: Modular Movement Holder.pdf Any feedback welcome!     I'm also going to make a parametric ring insert for rectangular/oval movements - but I just finished a parent teacher evening so too tired now 🙂  
×
×
  • Create New...