Jump to content

Most Useless Watch Tool

jdrichard

By jdrichard
in Tools & Equipment

 Share

Recommended Posts

MrRoundel Super WRT Addict

MrRoundel

Posted
Posted

I have a crystal lift like that, made by Vigor. It works, but seems a bit sketchy at how it grabs the edges of soft plastic with sharp metal. I'm sure that it puts scratches around the crystal even if you can't see them without magnification. Plus, it's always a pucker-factor 15 to get the crystal's diameter decreased enough to get it inserted. But since I don't have the proper Longines wrenches for monocoque cases, it's all I can use.

 

  • Like 2
Link to comment
Share on other sites
jdrichard Distinguished Member

jdrichard

Posted
  • Author
Posted
I have a crystal lift like that, made by Vigor. It works, but seems a bit sketchy at how it grabs the edges of soft plastic with sharp metal. I'm sure that it puts scratches around the crystal even if you can't see them without magnification. Plus, it's always a pucker-factor 15 to get the crystal's diameter decreased enough to get it inserted. But since I don't have the proper Longines wrenches for monocoque cases, it's all I can use.
 

Just need a proper plastic crystal press.


Sent from my iPhone using Tapatalk Pro
Link to comment
Share on other sites
MrRoundel Super WRT Addict

MrRoundel

Posted
Posted
2 hours ago, jdrichard said:


Just need a proper plastic crystal press.


Sent from my iPhone using Tapatalk Pro

You mean a GS type press? I do have one, but for some reason I didn't think it would work on my monocoque Wittnauers, etc. My thinking is that the GS press that I have, you have to put the crystal facing down in the support. The case, generally without a back, has to go over the plunger facing downward in order drop over the crystal. With the one-piece case, the back is not removable, so the plunger cannot pass through a bezel or open back case. Am I wrong, or is this a different type than you are referring to?

Link to comment
Share on other sites
Tmuir Distinguished Member

Tmuir

Posted
Posted

I use mine regularly, as vinn3 states on vintage watches.

Just used it the other day to fit a 14.4mm crystal onto a late 1950s ladies Certina.

That's the smallest crystal I've fitted and it was nearly at the limit of my tool as I just have the cheap Anchor brand one, but it has worked every time I have used it..

You also need the small base for holding the crystal for the tool to work though, this makes the claw grip the crystal just off the base of it so you can drop the crystal home whilst still compressed and then release the tension and it just expands into place.

  • Thanks 1
Link to comment
Share on other sites
AndyHull Distinguished Member

AndyHull

Posted
Posted

I've just used both the lift tool, and the crystal press, in the process of fixing a Timex. They are a little tricky to get right, and they don't work well in every case, and I did manage to drop the movement on the floor due to my ham-fisted efforts with the lift tool.

I wouldn't say it is  *THE* most useless tool, but perhaps one of the most tricky to use, and not appropriate for some crystals.

Popping the crystal out is often much easier with your thumbs, but obviously you can't do that with a front loader.

  • Like 1
Link to comment
Share on other sites
AndyHull Distinguished Member

AndyHull

Posted
Posted

I was going to nominate one of these... 

hammer.jpg&f=1

... but I believe there are a few people who use them to 're-allign' Timex watches.

Sacrilege to my eyes.

Using it to 're-alligning' an overpriced  Daniel Wellington, or maybe a dime store quartz possibly I could forgive, but not a Timex.  :P

  • Like 1
Link to comment
Share on other sites
jdrichard Distinguished Member

jdrichard

Posted
  • Author
Posted
just used my crystal lift on a friends roamer(question posted earlier!) and it was a doddle both off and on.mine is a Liberty made in india,a good price and quite solid.does the job well.also use a crystal press when needed.both handy to have.B

I find removing the crystal May be ok, however, installing it with those very touchy claws is way too difficult.


Sent from my iPhone using Tapatalk Pro
Link to comment
Share on other sites
jdrichard Distinguished Member

jdrichard

Posted
  • Author
Posted
I was going to nominate one of these... 
hammer.jpg%26f=1&key=b24d126953cea2e57cb43cdd67a9e6af46678fe4b0c8ddde7ceb61f3949788fa
... but I believe there are a few people who use them to 're-allign' Timex watches.
Sacrilege to my eyes.
Using it to 're-alligning' an overpriced  Daniel Wellington, or maybe a dime store quartz possibly I could forgive, but not a Timex.  [emoji14]

Is that a Left or Right Handed Hammer?


Sent from my iPhone using Tapatalk Pro
  • Haha 1
Link to comment
Share on other sites
jdrichard Distinguished Member

jdrichard

Posted
  • Author
Posted
I've just used both the lift tool, and the crystal press, in the process of fixing a Timex. They are a little tricky to get right, and they don't work well in every case, and I did manage to drop the movement on the floor due to my ham-fisted efforts with the lift tool.
I wouldn't say it is  *THE* most useless tool, but perhaps one of the most tricky to use, and not appropriate for some crystals.
Popping the crystal out is often much easier with your thumbs, but obviously you can't do that with a front loader.

I too use my thumbs to pop out the crystal and a front loader would need the claws??


Sent from my iPhone using Tapatalk Pro
Link to comment
Share on other sites
AndyHull Distinguished Member

AndyHull

Posted
Posted
3 minutes ago, jdrichard said:


... and a front loader would need the claws??
 

I grabbed the crystal with the claws, then held the lift tool between my knees and gave the movement plate a playful tap with a plastic rod and the useless tool I mentioned above.

Not the most subtle method, but very reliable for sending the watch in to orbit, and you do need to do that at least once a week, or you 'aint trying hard enough. Second try worked like a charm, and the movement, crystal and movement plate parted with the case quite nicely.

Something makes me suspect there may be a better way of doing this. 

  • Like 1
Link to comment
Share on other sites
m1ks WRT Addict

m1ks

Posted
Posted

I nominate the 3D printed mainspring winder that I printed and tried yesterday which successfully butchered a Seiko 7019A mainspring for me. :thumbsu:

At least that spring wasn't in the best fettle to begin with.

Back to winding in by hand unless someone wants to donate a spring winder set?:D

  • Like 2
Link to comment
Share on other sites
jdrichard Distinguished Member

jdrichard

Posted
  • Author
Posted
I nominate the 3D printed mainspring winder that I printed and tried yesterday which successfully butchered a Seiko 7019A mainspring for me. :thumbsu:
At least that spring wasn't in the best fettle to begin with.
Back to winding in by hand unless someone wants to donate a spring winder set?[emoji3]

Spring winder sets are easy to find on eBay. Or just do it by hand.


Sent from my iPhone using Tapatalk Pro
Link to comment
Share on other sites
jdrichard Distinguished Member

jdrichard

Posted
  • Author
Posted
I nominate the 3D printed mainspring winder that I printed and tried yesterday which successfully butchered a Seiko 7019A mainspring for me. :thumbsu:
At least that spring wasn't in the best fettle to begin with.
Back to winding in by hand unless someone wants to donate a spring winder set?[emoji3]

But you printed a mainspring winder?! Do you have a photo.


Sent from my iPhone using Tapatalk Pro
Link to comment
Share on other sites
Tmuir Distinguished Member

Tmuir

Posted
Posted

I wonder if I could scale that up to work with my aircraft clocks as the NOS alloy mainsprings I've got I can't wind in by hand and they are too big for all my watch spring winders and too small for my clock spring winders.

 

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • watchweasol
      Without Our Forum

      By watchweasol · Posted

      Hi guys, the question is what is a forum, a place for discussion and passing on information, idle chat and a bit of fun and I for one are the richer for it. When in Hospital last year with the Covid being force fed oxygen and feeling total sh1t and close to the pearly gates a daily look on the forum to see what was going down helped to keep me focused on the job in hand took my mind off the problem for a short while but it was a lifeline for sure. We chat to friends for that is what they become around the world read their posts help where we can post information where we can.  I like @Neverenoughwatches some times think of members past and wonder if they are still at the watches or given up, some drop in for advise and drop out again never to be heard of again. The forum reminds me of Yorkshire hospitality, The door is always open and the kettle on the stove. Long may it continue.   My two bobs worth.
    • KenD
      Main spring

      By KenD · Posted

      Thanks all.   Movement is a Helvetia 800C. Don't know any history e.g. if the broken mainspring is original. Watch was bought recently as non-working. Really interesting piece that Jon, thanks. I'd only been thinking of length relating to power reserve. I don't have a mainspring winder (yet) so I'd like to avoid winding the spring into the barrel by hand. The old spring measures at 1.60 x .11 x ~290. Sorry, can't be exact on the length. The piece I still have is 275, but the second piece escaped during measurement. Best measurement I had for it was ~13. The micrometer does zero accurately so I'm pretty confident of the .11 Also, I'm getting the barrel ID at 9.5 on a vernier. I'm now wondering about going with a .11 spring? Given all of the above, maybe 1.60 x .11 x 300 x 9? Any thoughts? Cheers.
    • VWatchie
      Without Our Forum

      By VWatchie · Posted

      Funny that you should bring this up. I was thinking about it just the other day. What happens if something happens to @Mark? The social bit is fantastic and I would miss it dearly, but I worry even more about the content. Together we have created a gold mine of information which would be more or less irreplaceable if the site should disappear. People (often with a lot of knowledge) come and go. I sometimes wonder what happened to them and miss them. We have no idea unless we have some private contact information. When I was new here I saw a lot of posts by @Lawson. He had a true fire in his heart for horology and was asking for an apprenticeship in his signature. I found that very inspiring and often wondered what happened. Is the fire still burning? Did he get an apprenticeship?
    • clockboy
      Intro

      By clockboy · Posted

      Welcome to the forum, enjoy.
    • Neverenoughwatches
      Without Our Forum

      By Neverenoughwatches · Posted

      I dont like to give up things that i enjoy Tom.  So my next question is how are we going to prepare for that inevitability and what are we going to do about it. Its not just about funding it but I did pick up on something that Mark said once. It doesnt run on fresh air , what if it becomes a burden or an unnecessary cost or for any other reason that i wont get into. We all know life can change in an instant, my life has been so up and down for about 8 years and was only just beginning to level itself out. 
×
×
  • Create New...