Jump to content

roamer quartz


Recommended Posts

my friend gave me a roamer quartz to look at but i dont know how to get inside! the back appears to be one piece and there is no where to put a case knife.there is an indentation near the crown but no where to get a purchase.in fact it just looks more like a DENT!.Do i have to take the crystal off?( i have done this before) But how do i remove the stem?

2019-05-16 16.40.25.jpg

2019-05-16 16.40.57.jpg

2019-05-16 16.41.22.jpg

2019-05-16 17.48.29.jpg

2019-05-16 17.49.52.jpg

Link to comment
Share on other sites

Hi Bernie   If it is indeed a monobloc case the stems are usually split stems and the crown and part of the stem clips out allowing the removal of the movement,  and access to the second part of the stem in the watch. Some require some force but be careful and pull straight so as not to damage the stem and not too much force and  damage the keyless work. one method is to use top cutters and a piece of tough thin plastic between the cutters and the button to protect if from marking

  • Thanks 1
Link to comment
Share on other sites

Your case looks like ones that are used by Wittnauer and Longines, among a few others. On these you have to "blow" the crystal through the case tube after removing the crown. It should be a two-piece stem that has to be pulled smartly, perhaps with a set of nipper pliers. If the case is karat gold, you should be extra careful about where the jaws are levering. But that's how I've pulled them out of Wittnauers with such case.

Usually there will be an engraving on the back that says something like, "Use 1260 wrench". These squeeze the crystal to remove it, rather than having to blow the crystal with a syringe.  I don't see it on yours, so maybe I'm missing something. Good luck.

Looks like Watchweasol beat me to the draw. But they do say the same thing, in essence..

Edited by MrRoundel
  • Thanks 1
Link to comment
Share on other sites

Most but not all of my all Roamers are housed in a “brevete waterproof” case which pushes through from the front with a little pressure from the thumbs, no tools required to get to the movement.


I can't say that yours is the same but a clearer picture from the crown side i.e. picture 4 & 5 should allow confirmation if yours is of a similar design.



Sent from my moto g(6) play using Tapatalk

  • Thanks 1
Link to comment
Share on other sites

You can tilt the movement out once you remove the crystal.Them stem would be in two pieces, a sort of male/female arrangement. The part attached to the crown being split.With the movement slightly tilted rotate the crown, feel for the spot where the split is perpendicular to the case, it will be obvious to you when it is as the movement will have the most tilt. It should then tilt out pretty easily.

  • Thanks 1
Link to comment
Share on other sites

On 5/17/2019 at 3:43 PM, berniethebolt said:

thanks to all that answered my query.it was indeed a split stem which i managed to pull out with forefinger and thumb!used my crystal lift replaced the battery and bobs your uncle.gratefully yours,the Bolt.

further to this post things did not go as well as i thought:i changed the battery and the second started off on its way then after a while it stopped and just jerked a little.it pulses a little but that is it.the movement is an eta 555-415 and i have found a service chart but i am loathe to take it apart as i am more comfortable with a mechanical movement.any ideas? can it be kick started?B

Link to comment
Share on other sites

Hi bernie, May need just a clean.

To kick start, put some lighter fluid on jewels/ holes of the gear train you can reach, push an accessible wheel to make it go.

Any evidence of water/ moisture having got to the EB? Water ruins the EB and it behaves as you described, not repairable.

  • Like 1
Link to comment
Share on other sites

Quartz movements make me cringe.you could try flushing it out with a plastic safe electronic spray cleaner. I have had mixed success with it. Don't hit it with a full force blast , just let it sort of dribble through you will be surprised at the gunk you wash out. let it dry in the sun.

Edited by yankeedog
content
  • Like 1
Link to comment
Share on other sites

1 hour ago, yankeedog said:

Quartz movements make me cringe.you could try flushing it out with a plastic safe electronic spray cleaner. I have had mixed success with it. Don't hit it with a full force blast , just let it sort of dribble through you will be surprised at the gunk you wash out. let it dry in the sun.

 

1 hour ago, Nucejoe said:

Hi bernie, May need just a clean.

To kick start, put some lighter fluid on jewels/ holes of the gear train you can reach, push an accessible wheel to make it go.

Any evidence of water/ moisture having got to the EB? Water ruins the EB and it behaves as you described, not repairable.

will give both a try.was thinking of replacing with a 955.412 which seems to be the same size and is available from cousins from around £23 with postage if my friend wants to go that way!

Link to comment
Share on other sites

  • 1 month later...
On 5/19/2019 at 3:22 PM, berniethebolt said:

 

will give both a try.was thinking of replacing with a 955.412 which seems to be the same size and is available from cousins from around £23 with postage if my friend wants to go that way!

Further to this post I obtained a 955.412 which came with a normal stem. I tried the original stem but it didn't fit. Tried to look for split stem for this movement but have not had any luck. Any ideas? B. 

Link to comment
Share on other sites

Cousins are showing that they have a male inner stem for the 955.412 in stock. Length is 9.79mm. ETA956101964 (Disregard the "Swiss Part Description" filter and just search by caliber and scroll through the result set, it will be towards the end of the list.)

Bit confused though as the Ranfft site shows that both the 955.412 and 555.412 as having the same stem reference.

Probably best to measure the original split stem and check that the ends of both stems that you have actually match.

Hope that this is of some use to you.

Nigel



Sent from my moto g(6) play using Tapatalk

  • Like 1
Link to comment
Share on other sites

6 hours ago, nad said:

Cousins are showing that they have a male inner stem for the 955.412 in stock. Length is 9.79mm. ETA956101964 (Disregard the "Swiss Part Description" filter and just search by caliber and scroll through the result set, it will be towards the end of the list.)

Bit confused though as the Ranfft site shows that both the 955.412 and 555.412 as having the same stem reference.

Probably best to measure the original split stem and check that the ends of both stems that you have actually match.

Hope that this is of some use to you.

Nigel



Sent from my moto g(6) play using Tapatalk
 

the male inner stem seems right but i will need a new female stem as the original is now a little short to fit this movement!they sure dont make it easy do they? thanks for your help.fingers crossed! B.

Link to comment
Share on other sites

Look under Generic Watch Parts Stem Extensions on the Cousins site. I've used the female extensions in the past. They screw into the crown and you need to cut them to length to ensure that it engages correctly with the male inner stem.

They currently only show a limited number of tap sizes. As such you may have to replace the crown as well if what they have available is a different tap size to the current crown.





Sent from my moto g(6) play using Tapatalk

  • Like 1
Link to comment
Share on other sites

5 hours ago, nad said:

Look under Generic Watch Parts Stem Extensions on the Cousins site. I've used the female extensions in the past. They screw into the crown and you need to cut them to length to ensure that it engages correctly with the male inner stem.

They currently only show a limited number of tap sizes. As such you may have to replace the crown as well if what they have available is a different tap size to the current crown.





Sent from my moto g(6) play using Tapatalk
 

Just ordered it. Will let you know how I get on. B

Link to comment
Share on other sites

  • 1 month later...


  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Hi guys I think that old hippy is correct, it opens the gates for china to manufacture aftermarket spare parts. considering that they already do work on behalf of the Swiss I guess this decision gives the a little more legitimacy to tool up and I am sure they will take advantage of the situation either with or without the blessing of the Swiss watch industry  Having read about the protectionist machinations of the Swiss in the history of Europe they were the only ones to get fat at everybody else’s expense. I think the outcome could have been guessed at but ,  fair play to Cousins UK for standing up to them.  Now the question,  will everybody boycott Swiss watches and Swatch, no way they will still fill their coffers.  Me I stick with the Japanese once renowned for cheap shitty watches who came good through industrial effort and don’t for get the Russians that most dismiss as low grade crap. Wouldn’t buy a swatch product ever how about you all.? a
    • Hold the crown when in winding position, move the click away from the crown wheel, and then while holding the crown let it slowly unwind. I recollect that you must remove the automatic device bridge first, but maybe I'm wrong. You can first try without removing the automatic device bridge.
    • nevenbekriev- You nailed it with your description of me and my reaction when the clock started ticking again. I am a newbie.  I love the sound and idea of mechanical clocks but the idea of owning one and trying to keep them running has never appealed to me. My wife bought this one and an antique German wall clock.  When I looked into having someone repair them for me, the universal response was "it's really expensive to work on them, you should just replace the movement". So, I had nothing to lose, I started researching them and opened them up. The wife is happy because she hears the sound of the clocks again. But I have gone down the "accuracy" rabbit hole. In the vertical position, the balance wheel was not floating. It was sitting on the bottom of the frame. I adjusted the lower spring collet and got it floating. It easily passed the 270 degree 3 to 5 minute oscillation test. It took 8 minutes for the wheel to completely stop moving.  I put it the unit back in the movement and checked the safety pin. It does not touch the safety roller anywhere in +/-270 degrees rotation from neutral position. But the amplitude of the rotation with the spring fully wound is weak based on what you are saying. It rotates +/-90 degrees from the neutral position.  No, I did not take the movement completely apart.  That seemed way outside my skill set at the time. There is a reason I became an electrical engineer and not a mechanical engineer. I am much more comfortable with moving electrons than tiny moving metal parts. Will I do it in the long run? Anything can happen. I don't seem to be able to let it go.
    • Isn't that the same guy who told Zelenskyy to escalate the war with Russia/Putin when they already had a peace deal? 2 years later and we have half a million young Ukranian boys dead. He doesn't seem very clever...
×
×
  • Create New...