Jump to content
  • Similar Content

    • By wilding
      Hello there watch fix fans. Here's (I hope) an interesting one for you.
      I have this beautiful small ladies 'Fero Feldmann' Swiss-made watch - it came in a bag of "used and to be repaired" watches.
      From what I can see, the mechanism seems in very good working order. Just a slight shake and it goes and goes. There is no strap, but that is not the issue here.
      The problem is the stem and/or crown. As you can see, there is definitely no crown. But I am wondering about the stem.
      The watch does have its case and edoes have, as you can see, a hole where the stem and/or crown will/should fit in.
      There is something which appears to be some kind of part-stem at the 3 o'clock position.
      Using tweezers I can pull it out and push it back in quite freely. A very small screw on top holds this "stem" in place. I think you can see, in ths second photo, how this "stem" attaches to the rest of the movement.
      Clearly I need to attach a crown. BUT what about a stem? A stem extension? Or one of those crowns which has an extended stem-like attachment which should fix onto this current "stem" in this watch?
      Yes, the watch face is somewhat scratched, and the minute hand is a little bent at the top. You may say it is not worth my while trying to get this fixed. But I just SO MUCH like this little watch and would LOVE to give it life again! It clearly IS still "alive" - though I'm not sure if it is a mechanical wind-up or an automatic. The latter of these seems to be the case - as I said earlier, a little shake and the mechanism goes and goes. PErhaps with a little oil (and lots of encouragement) it can be made good.
      So my main question - what kind of stem/crown to attach and how to do it?
       


    • By examiner
      How to remove this winding stem? I don't know what I should push to remove this winding stem.

    • By Heman
      Hello all,
      I have a watch I would like to fix my self. It's made by TAWATEC, who is no longer in business. It's very similar to a Luminox and used TGS for lume. I will provide information to the best of my ability. 

      Here is a link to some information about it. Here are a few pictures of the watch. 

       


       
      I have had the watch since May of 2011. I had the battery replaced in Feb 2015 by a local shop. Less than a year later, I noticed that after taking a shower there was condensation under the crystal. I pulled the crown and left it sit to air out. After about a week I pushed the crown back in and the watch no longer worked. I wondered what caused it to leak. I then remembered I had to change the date on the watch a few days before condensation had got inside the watch. When I was trying to set the date I noticed that it was difficult to pull the crown out and it was more difficult to turn than usual. My guess was that the gasket/O-ring that is on the stem/crown was messed up and had ripped and water had entered that way. I left the watch sit for a year and used another watch as my daily driver. I'm hoping to get this one up and running again. So I recently decided to see if I could fix the watch myself. 
       
      Here is what I have done and have figured out so far...
      I was able to remove the case back by removing the 4 Phillips screws. Visually inspecting the O-ring that seals the case back, everything looks good. The movement is a Ronda 515. The plastic ring that holds the movement inside the case says Ronda 515 # 6. I was able to remove the crown and stem. Looking towards the inside of the crown there was remnants of the O-ring. After clearing the remnants and putting the crown back in, the crown moves freely. I also found remnants if rubber on the front of the dial. After inspecting the battery, it looks to have leaked its electrolyte What I would like to do first is replace the O-Ring that's on the crown and put a new battery in it. If I then determine that the movement is damaged, I can replace it later. 
      What do I need to do to figure out what size of O-ring I need for the crown? I can take pictures of the crown/stem if needed. I also have analog calipers to use that are in inches.
      Thanks for your time!
       
       
    • By lucasantarella
      Hi All,
      I recently replaced the movement for my Tissot PR50, which was a standard ETA F06.111. I now need to replace the crown as the old stem was broken into the crown and could not be re-used.
      Could someone point me in the right direction in finding a proper replacement crown? I don't know the size or how/where to measure to find a proper crown.
      Thank you!
    • By Wesley881
      Hi all,
      My goodness it's been a while since I've posted and boy have I missed this forum! Feels good to catch up on a few new tales of triumph, trials and tribulations.
      I have a Waltham model 1910, 37 size chronometer that I recently had some help getting a new staff for. Now it's time to find a crown. Problem is, the common car clock case for this movement has a 6.80mm neck, but the weighted case for the ship chronometer has a 7.20mm neck. Any ideas of sourcing something like this short of making one? I'm browsing Cousins at the moment...
      Cheers
  • Recently Browsing

    No registered users viewing this page.

  • Topics

  • Posts

    • I hand clean and only use the lighter fluid for one-dip, what is the cheaper refined alternative you're referring to? I'm focusing on buying proper oils before getting fancy with my cleaning setup, so I'm hand cleaning for now with mineral spirits in a scrub then rinse.
    • That is good news. I have never heard of that trick. 
    • I'm so frustrated... after cleaning and oiling the bottom cap jewel and the upper jewel it works much worse, anchor snaps when rotating the wheel manually but it does not swing on its own any more  I used 9010 oil. I will just try to oil the pivots a bit more and make sure all is properly aligned... this tiny movement drives me crazy.
    • Hi all, I've finally put my foot through the door of the world of chronographs, and I got an excellent deal on a gold cased Luxor chronograph with a Landeron 248 movement. The dial looks perfect, so perfect at such a price I assume it was either redialed or a miracle occurred when my offer was accepted. The only flaw to the watch is the second recorder resets to about 1 -2 minutes past 12, every time. I thought initially the second hand just needed adjustment, until I noticed the minute recorder will advance a minute when the second recorder crosses midnight exactly, but still resets at 1-2 past 12. This means a recorded minute is actually 58ish seconds. So adjusting the second hand won't solve this problem, and I'm very curious what about this movement syncs these two registers.   If anyone has advice, it would be appreciated.
    • The warm water has worked, 3 days of waiting sorted in 30 seconds in warm water  should have thought of it earlier
×
×
  • Create New...