Jump to content

Hello from NYC!

LumeShot

By LumeShot
in Introduce Yourself Here

 Share

Recommended Posts

LumeShot Member

LumeShot

Posted
Posted

Hello everyone! Just recently starting investing into better watch making tools and wanted to get more involved with forums (specifically about watch making). Some of you guys might know me from Youtube and Instagram. 

Just a quick introduction!

I've been working on watches for about two years now I believe. Mostly on Seiko watches since the amount of parts available is so vast. I've learned everything myself through reading material online and just getting myself involved. Learning from my mistakes was the biggest help for sure. Like most people, I started with more affordable tools, which helped me become extremely careful and detailed since the calibration of the tools were horrible. I've now seriously invested in quality tools since I am working on watches much more frequently (as a hobby) and wish to learn more about them and their usages/maintenance! 

Thanks for reading and I'm excited to join this forum! 

-Eric

 

 

  • Thanks 1
Link to comment
Share on other sites
oldhippy Distinguished Member

oldhippy

Posted
Posted

Thank you for your introduction and welcome to this friendly forum.

Good tools are a must if you are serious about repairing.

I always used dumont tweezers and  Bergeon Watchmakers Screwdrivers and don't forget the right oils.

Link to comment
Share on other sites
LumeShot Member

LumeShot

Posted
  • Author
Posted
On 5/10/2019 at 4:41 AM, oldhippy said:

Thank you for your introduction and welcome to this friendly forum.

Good tools are a must if you are serious about repairing.

I always used dumont tweezers and  Bergeon Watchmakers Screwdrivers and don't forget the right oils.

Thank you! The existing posts and discussions have been extremely interesting to learn from. I'm really glad I made the choice to upgrade my tools. Now I just got to get the rest of it over time. Really starts to add up when you consider two Dumostar tweezers can run close to a $100! I realized I will find out which tools I will need to invest in after I learn more about movement servicing.

I've recently bought a Dumostar #2, a #3 and a #5, in addition to hi-tech series #2 and #1 ( realized the Dumostar will be superior, but first I hope to learn from the hi-tech series on proper tweezer usage so that I don't risk messing up the Dumostar ones ). I also bought a Bergeon 30081-S09 set. I was looking into horotec, but the cost was quite high and also wanted to learn from the Bergeon set before investing in the horotec 12 piece set ( so that I can learn proper usage first before mishandling a $300+ horotec set ). 

I've come to really appreciate well made tools. The craftsmanship in watchmaking is always incredible, but something about well made tools also gets me quite happy. 

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • arron
      Ball PW balance staff and hands

      By arron · Posted

      @JohnR725 that's very helpful.  I appreciate the time you took to give those instructions and post the pictures.  below is a picture of my staff, which looks identical to the ones you posted.  The approx measurements I got are: .772 on the left part of the staff; .715 on the right side of the hub; the hub is 1.107; and the overall length (minus the broken pivot) is 5.248; which seem to line up with the measurements you posted.  I didn't think to measure the pivot, which I'll do if there's enough of one left on the staff.  Thanks again.
    • DDean
      Incabloc Lyre Spring & Low Earth Orbit

      By DDean · Posted

      Thank you to both of you!  I've been somewhat derailed by this quandary for a couple of days now. I am guessing that the point of the wider tweezers is to support the whole spring at the same time in an effort to prevent it going under tension... I have already discovered the Zen of a clutter free space, and trying to keep my work well away from the edge, however the most terrifying of the flights wasn't so short, I had my work in the middle of the table and nothing else around.  That particular launch was towards me.  I distinctly recall feeling the spring hit my left hand as it escaped.  I only found it by dumb luck, on the floor, between the legs of my chair.  I need to order a pack of replacements just in case.  I think I recall a thread discussing where to find them, and the differences between the clones and the authentic ETA ones, pointing out that they're not interchangeable (the clones being longer IIRC).  Now I just have to find that thread again.  What I haven't mastered is the zen of the search function here.  I'm sure I"ll get that down eventually. So this is similar to, but different from one of the posts I had found in my original searches (or maybe I'm just hallucinating, I can't find the post I thought I remember).  The bits about the corner filled in a gap in what I'd read before.  At least I have a more clear picture in my head about what needs to happen now.  Yes, I've learned about how touchy these springs are.  What I'm not sure I have a good grasp on is the understanding of what causes the spring to flex, other than to say "the slightest little touch"  I think I'm going to try a small bit of Rodico to position the spring next time.
    • HectorLooi
      Casio AQ-321G Battery

      By HectorLooi · Posted

      I think it's stamped on the inside cover. 309 I think.
    • Waggy
      Casio AQ-321G Battery

      By Waggy · Posted

      Hi all, needing a little help. I have an old Casio AQ-321G, but have no idea what battery it takes. I've looked around online, but cannot see anything... I see a 309 stamped on the case back, could this be it....? Can you please help, below are some pictures:
    • nevenbekriev
      'Services' Chronograph

      By nevenbekriev · Posted

      The radial teeth are for hte seconds register, and the other (which is simple and doesn' take away significant torque from the train) for the minutes register.
×
×
  • Create New...