Jump to content

Radial Brushed Steel Look

margolisd

By margolisd
in Watch Repairs Help & Advice

 Share

Recommended Posts

margolisd WRT Addict

margolisd

Posted
Posted

Hi guys. I have a cosmetic question. This 1970s Omega Dynamic has a kind of radial sunburst brushed metal looks around its edge. I've been trying to restore it today. I polished it down to get rid of all the nastiness. But I've really struggled to find a good technique to get the brushed effect back onto the polished surface.

I ended up hot gluing the case to a platform that fitted into my jeweling tool. And after centring it I used thin strips of sandpaper to try and create consistent strokes and rotating the case a tiny bit at a time. It looks better with the the worst nicks and scratches gone. But the brush lines aren't as good as they were originally. How might this look have been achieved in the factory? And is there a less hacky way I can improve this?

s-l1600.jpg

IMG_1561.png

IMG_1571.png

Link to comment
Share on other sites
jdm Distinguished Member

jdm

Posted
Posted
2 hours ago, rogart63 said:

DSC04517.thumb.JPG.2d1fb4df297fe5521e1d1fcae6f5dedf.JPG

Very well done. On the Unimat 3 right? I suppose you left the toolpost lose and slid by hand?
I'm awaiting delivery of a lathe like that, for casework. Can't wait and I become a bit fixated about.
 

  • Like 1
Link to comment
Share on other sites
rogart63 Distinguished Member

rogart63

Posted
Posted
5 hours ago, jdm said:

Very well done. On the Unimat 3 right? I suppose you left the toolpost lose and slid by hand?
I'm awaiting delivery of a lathe like that, for casework. Can't wait and I become a bit fixated about.
 

I adjusted the tool post in the right angle and just slide the wooden piece back an forth a few times and moved the case a little until i had done a full circle . Maybe a harder  wood or an aluminium stick would have worked better. But it was a lot better then the polished case that was before. I left the 2 screws loose  so i could slide the stick. And yes it's a Unimat 3.  Probably 30 years old or more.  have done a lot of things on that.  On this picture i have it loose but now it's on a big piece of wood. And i have cleaned it up a bit. Had been in a garage for some years without much use.  So looks a little rusty. Buts' in pretty good condition . They are  real workhorses this lathes. 

I am after a watchmakers lathe-. But so far i haven't found anything that is good and have an okay price. 

Link to comment
Share on other sites
margolisd WRT Addict

margolisd

Posted
  • Author
Posted

That's a great approach Rogart. I spent a bit more time using my technique. It looks fainter than the original but I'm relatively happy with it now. I could probably get it better with coarser sandpaper. But then that might just highlight the imperfect lines. I really need a lathe.

IMG_9138.png

Link to comment
Share on other sites
saswatch88 WRT Addict

saswatch88

Posted
Posted
9 hours ago, rogart63 said:

Have done a few in my lathe. This is a Omega f300 cone i did.  About the same as you did. Had to laser weld the case as it had some large marks. 

anyway you can upload a video? I been wanting to know how to do this myself, ive tried different methods, however i dont have a lathe. There is no videos out there on lapping.

Link to comment
Share on other sites
jdm Distinguished Member

jdm

Posted
Posted (edited)
53 minutes ago, saswatch88 said:

anyway you can upload a video? I been wanting to know how to do this myself, ive tried different methods, however i dont have a lathe. There is no videos out there on lapping.

What Rogart has done is not lapping, he ingeniously used the geometry of the lathe to keep filing at the right angle. The same setup could be replicated with a fixture all made of wood. 

Edited by jdm
  • Like 1
Link to comment
Share on other sites
jdm Distinguished Member

jdm

Posted
Posted
28 minutes ago, saswatch88 said:

yea i get that but would be nice to see a how to video

When you search watch case refurbish on YouTube there are so many videos. For brushed parts the fundamental is always the same, straight action with the right grit. 

Link to comment
Share on other sites
rogart63 Distinguished Member

rogart63

Posted
Posted

 

6 hours ago, saswatch88 said:

i dont have a lathe 

You can do a simple fixture  out of  wood and something to hold the case in. So it can be turned around in the same way as in a lathe. See if i can find anything 

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Geotex
      Any tips to correct a sloppy error?

      By Geotex · Posted

      That's a good idea - shrinking down the nut and wrench size from the old casebook trick!
    • GuyMontag
      Movement holder made with 3D printer

      By GuyMontag · Posted

      I missed this earlier. The dial isn't going into the holder, it should sit proud of it. This is what I am currently using which I print for each different movement.    
    • Neverenoughwatches
      Setting lever spring

      By Neverenoughwatches · Posted

      I didn't think pulling to set position would work harden the spring, in that position it is stressed where the arm starts. By work hardening i meant rapid polishing at that point, a bit like polishing a pivot work hardens as it compresses the steel. I doubt polishing by hand would achieve much in that respect though. Its finished, arm polished up mostly at the join to the bridge's main body. I'm ok with it, the screw holes aren't great as i had to open them up by redrilling and positioning it was difficult, I'm not much use with a loupe, opening up with a file might be a better option for me or i could just use the correct drill size 😅. And the detent is way too deep, i had to guess that with the stem release out of position and sat on top, but i only took one measure and went for it, no slowly slowly catch your monkey 😅. First go I'm happy , well sort of, it works and thats a big thing for me, next one will have a bit more finesse.  Anyone thats interested, after filing, i used a 2000 grade home made diamond  micro file and then 20 micron film, the film is much better than wet and dry, more stable to use and doesn't shed cheap grade grit everywhere , then auto polish on a sponge pad.
    • RichardHarris123
      Setting lever spring

      By RichardHarris123 · Posted

      I'm assuming that every time you set the watch you are work hardening the detent spring, maximum hardening is  where it meets the plate due to maximum deflection.   That's why it snaps there.  The Young's modulus may be the same but after it's reached its maximum yeid strength it breaks.  My mechanic engineering is very rusty, correct me if I'm wrong. 
    • Neverenoughwatches
      Setting lever spring

      By Neverenoughwatches · Posted

      Ah ok yes that makes sense to polish it where the arm starts to form from the body of the bridge, i thought you meant the underneath of all the arm.
×
×
  • Create New...