Jump to content

Radial Brushed Steel Look

margolisd

By margolisd
in Watch Repairs Help & Advice

 Share

Recommended Posts

margolisd WRT Addict

margolisd

Posted
Posted

Hi guys. I have a cosmetic question. This 1970s Omega Dynamic has a kind of radial sunburst brushed metal looks around its edge. I've been trying to restore it today. I polished it down to get rid of all the nastiness. But I've really struggled to find a good technique to get the brushed effect back onto the polished surface.

I ended up hot gluing the case to a platform that fitted into my jeweling tool. And after centring it I used thin strips of sandpaper to try and create consistent strokes and rotating the case a tiny bit at a time. It looks better with the the worst nicks and scratches gone. But the brush lines aren't as good as they were originally. How might this look have been achieved in the factory? And is there a less hacky way I can improve this?

s-l1600.jpg

IMG_1561.png

IMG_1571.png

Link to comment
Share on other sites
jdm Distinguished Member

jdm

Posted
Posted
2 hours ago, rogart63 said:

DSC04517.thumb.JPG.2d1fb4df297fe5521e1d1fcae6f5dedf.JPG

Very well done. On the Unimat 3 right? I suppose you left the toolpost lose and slid by hand?
I'm awaiting delivery of a lathe like that, for casework. Can't wait and I become a bit fixated about.
 

  • Like 1
Link to comment
Share on other sites
rogart63 Distinguished Member

rogart63

Posted
Posted
5 hours ago, jdm said:

Very well done. On the Unimat 3 right? I suppose you left the toolpost lose and slid by hand?
I'm awaiting delivery of a lathe like that, for casework. Can't wait and I become a bit fixated about.
 

I adjusted the tool post in the right angle and just slide the wooden piece back an forth a few times and moved the case a little until i had done a full circle . Maybe a harder  wood or an aluminium stick would have worked better. But it was a lot better then the polished case that was before. I left the 2 screws loose  so i could slide the stick. And yes it's a Unimat 3.  Probably 30 years old or more.  have done a lot of things on that.  On this picture i have it loose but now it's on a big piece of wood. And i have cleaned it up a bit. Had been in a garage for some years without much use.  So looks a little rusty. Buts' in pretty good condition . They are  real workhorses this lathes. 

I am after a watchmakers lathe-. But so far i haven't found anything that is good and have an okay price. 

Link to comment
Share on other sites
margolisd WRT Addict

margolisd

Posted
  • Author
Posted

That's a great approach Rogart. I spent a bit more time using my technique. It looks fainter than the original but I'm relatively happy with it now. I could probably get it better with coarser sandpaper. But then that might just highlight the imperfect lines. I really need a lathe.

IMG_9138.png

Link to comment
Share on other sites
saswatch88 WRT Addict

saswatch88

Posted
Posted
9 hours ago, rogart63 said:

Have done a few in my lathe. This is a Omega f300 cone i did.  About the same as you did. Had to laser weld the case as it had some large marks. 

anyway you can upload a video? I been wanting to know how to do this myself, ive tried different methods, however i dont have a lathe. There is no videos out there on lapping.

Link to comment
Share on other sites
jdm Distinguished Member

jdm

Posted
Posted (edited)
53 minutes ago, saswatch88 said:

anyway you can upload a video? I been wanting to know how to do this myself, ive tried different methods, however i dont have a lathe. There is no videos out there on lapping.

What Rogart has done is not lapping, he ingeniously used the geometry of the lathe to keep filing at the right angle. The same setup could be replicated with a fixture all made of wood. 

Edited by jdm
  • Like 1
Link to comment
Share on other sites
jdm Distinguished Member

jdm

Posted
Posted
28 minutes ago, saswatch88 said:

yea i get that but would be nice to see a how to video

When you search watch case refurbish on YouTube there are so many videos. For brushed parts the fundamental is always the same, straight action with the right grit. 

Link to comment
Share on other sites
rogart63 Distinguished Member

rogart63

Posted
Posted

 

6 hours ago, saswatch88 said:

i dont have a lathe 

You can do a simple fixture  out of  wood and something to hold the case in. So it can be turned around in the same way as in a lathe. See if i can find anything 

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Knebo
      Epilame / Fixodrop

      By Knebo · Posted

      Hello everyone, for what it's worth, here is my approach: 1. Escape wheel submerged in Epilame, then dried quickly with a hairdryer. Then the final tip of the pivots are cleaned by poking into pithwood. The logic being that the Epilame is removed at the intended contact point (to avoid any residue that may mix with the oil), but remains in the areas where oil is not supposed to spread to (further down the pivot towards the wheel). The escape wheel teeth also benefit from having Epilame to keep the 9415 in place.  2. I use a syringe to treat only the pallet stones. I suspend the pallet fork with some Rodico so that the stones hang downwards. I notably use a rather thick needle where a drop WON'T form, but rather where the Epilame liquid stays in the needle tip, which I then dip into the pallet stones. It requires some practice to get the right amount of Epilame into the needle tip, but it works for me now. This way, no drop will "jump" onto the pallet fork and potentially go all the way to the pivots.  3. I let the movement run for a few minutes without lubricating the pallet stones... to scrape off the Epilame in the intended contact "channel". Then I remove the balance again and lubricate the exit pallet stone with 3-4 successive drops. See the "channel" that forms on the pallet stone in the picture -- not so easy to see, but it's visible.       I am conflicted about the use of Epliame in balance jewel settings. My impression is that the two jewels sufficiently suspend the oil (even 9010). Apparently Rolex recommends NOT to use Epliame there (heard from a former Rolex service center watchmaker), as it could cause additional wear. Apart from that, I follow specific instructions where I can find them. E.g. the infamous Rolex reverser wheels or sometimes (parts of) the seconds wheel. Exception: I'm currently servicing an Eta 2824 and will probably ignore the service sheet that recommends treating the whole keyless works with Epilame and then using HP1300... I'll skip the Epilame and use 9504 grease.        
    • GuyMontag
      Movement holder made with 3D printer

      By GuyMontag · Posted

      I'm going to give this a try today/tomorrow on my UTC33/Seiko 66, thanks!
    • RichardHarris123
      Intro

      By RichardHarris123 · Posted

      Hello and welcome from Leeds, England. 
    • oldhippy
      Without Our Forum

      By oldhippy · Posted

      Don't forget Mark is a hard working watch maker so he is also tied up with work. I'm sure he is keeping his eye on this forum making sure it is running along nicely. 
    • oldhippy
      Intro

      By oldhippy · Posted

      Thank you for your introduction and welcome to this friendly forum. We all look forward to your contributions and continued involvement.    
×
×
  • Create New...