Jump to content

Radial Brushed Steel Look


Recommended Posts

Hi guys. I have a cosmetic question. This 1970s Omega Dynamic has a kind of radial sunburst brushed metal looks around its edge. I've been trying to restore it today. I polished it down to get rid of all the nastiness. But I've really struggled to find a good technique to get the brushed effect back onto the polished surface.

I ended up hot gluing the case to a platform that fitted into my jeweling tool. And after centring it I used thin strips of sandpaper to try and create consistent strokes and rotating the case a tiny bit at a time. It looks better with the the worst nicks and scratches gone. But the brush lines aren't as good as they were originally. How might this look have been achieved in the factory? And is there a less hacky way I can improve this?

s-l1600.jpg

IMG_1561.png

IMG_1571.png

Link to comment
Share on other sites

2 hours ago, rogart63 said:

DSC04517.thumb.JPG.2d1fb4df297fe5521e1d1fcae6f5dedf.JPG

Very well done. On the Unimat 3 right? I suppose you left the toolpost lose and slid by hand?
I'm awaiting delivery of a lathe like that, for casework. Can't wait and I become a bit fixated about.
 

  • Like 1
Link to comment
Share on other sites

5 hours ago, jdm said:

Very well done. On the Unimat 3 right? I suppose you left the toolpost lose and slid by hand?
I'm awaiting delivery of a lathe like that, for casework. Can't wait and I become a bit fixated about.
 

I adjusted the tool post in the right angle and just slide the wooden piece back an forth a few times and moved the case a little until i had done a full circle . Maybe a harder  wood or an aluminium stick would have worked better. But it was a lot better then the polished case that was before. I left the 2 screws loose  so i could slide the stick. And yes it's a Unimat 3.  Probably 30 years old or more.  have done a lot of things on that.  On this picture i have it loose but now it's on a big piece of wood. And i have cleaned it up a bit. Had been in a garage for some years without much use.  So looks a little rusty. Buts' in pretty good condition . They are  real workhorses this lathes. 

I am after a watchmakers lathe-. But so far i haven't found anything that is good and have an okay price. 

Link to comment
Share on other sites

That's a great approach Rogart. I spent a bit more time using my technique. It looks fainter than the original but I'm relatively happy with it now. I could probably get it better with coarser sandpaper. But then that might just highlight the imperfect lines. I really need a lathe.

IMG_9138.png

Link to comment
Share on other sites

9 hours ago, rogart63 said:

Have done a few in my lathe. This is a Omega f300 cone i did.  About the same as you did. Had to laser weld the case as it had some large marks. 

anyway you can upload a video? I been wanting to know how to do this myself, ive tried different methods, however i dont have a lathe. There is no videos out there on lapping.

Link to comment
Share on other sites

53 minutes ago, saswatch88 said:

anyway you can upload a video? I been wanting to know how to do this myself, ive tried different methods, however i dont have a lathe. There is no videos out there on lapping.

What Rogart has done is not lapping, he ingeniously used the geometry of the lathe to keep filing at the right angle. The same setup could be replicated with a fixture all made of wood. 

Edited by jdm
  • Like 1
Link to comment
Share on other sites

28 minutes ago, saswatch88 said:

yea i get that but would be nice to see a how to video

When you search watch case refurbish on YouTube there are so many videos. For brushed parts the fundamental is always the same, straight action with the right grit. 

Link to comment
Share on other sites

 

6 hours ago, saswatch88 said:

i dont have a lathe 

You can do a simple fixture  out of  wood and something to hold the case in. So it can be turned around in the same way as in a lathe. See if i can find anything 

Link to comment
Share on other sites



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • although not in this case.  It was the Lugano Convention and its deficiencies that allowed a Swiss court decision in the first place.  This isnt really a Brexit issue at all.  A decision that affects both the EU and the UK should never have been heard in Switzerland. I bet the authorised service centres in the UK are pretty pleased.  It's a massive shame, though; I believe watch owners should be able to choose to have their watch serviced by whoever they trust.
    • Hi guys I think that old hippy is correct, it opens the gates for china to manufacture aftermarket spare parts. considering that they already do work on behalf of the Swiss I guess this decision gives the a little more legitimacy to tool up and I am sure they will take advantage of the situation either with or without the blessing of the Swiss watch industry  Having read about the protectionist machinations of the Swiss in the history of Europe they were the only ones to get fat at everybody else’s expense. I think the outcome could have been guessed at but ,  fair play to Cousins UK for standing up to them.  Now the question,  will everybody boycott Swiss watches and Swatch, no way they will still fill their coffers.  Me I stick with the Japanese once renowned for cheap shitty watches who came good through industrial effort and don’t for get the Russians that most dismiss as low grade crap. Wouldn’t buy a swatch product ever how about you all.? a
    • Hold the crown when in winding position, move the click away from the crown wheel, and then while holding the crown let it slowly unwind. I recollect that you must remove the automatic device bridge first, but maybe I'm wrong. You can first try without removing the automatic device bridge.
    • nevenbekriev- You nailed it with your description of me and my reaction when the clock started ticking again. I am a newbie.  I love the sound and idea of mechanical clocks but the idea of owning one and trying to keep them running has never appealed to me. My wife bought this one and an antique German wall clock.  When I looked into having someone repair them for me, the universal response was "it's really expensive to work on them, you should just replace the movement". So, I had nothing to lose, I started researching them and opened them up. The wife is happy because she hears the sound of the clocks again. But I have gone down the "accuracy" rabbit hole. In the vertical position, the balance wheel was not floating. It was sitting on the bottom of the frame. I adjusted the lower spring collet and got it floating. It easily passed the 270 degree 3 to 5 minute oscillation test. It took 8 minutes for the wheel to completely stop moving.  I put it the unit back in the movement and checked the safety pin. It does not touch the safety roller anywhere in +/-270 degrees rotation from neutral position. But the amplitude of the rotation with the spring fully wound is weak based on what you are saying. It rotates +/-90 degrees from the neutral position.  No, I did not take the movement completely apart.  That seemed way outside my skill set at the time. There is a reason I became an electrical engineer and not a mechanical engineer. I am much more comfortable with moving electrons than tiny moving metal parts. Will I do it in the long run? Anything can happen. I don't seem to be able to let it go.
×
×
  • Create New...