Jump to content

Screwdrivers, what to buy?


Bod

Recommended Posts

Now I have a problem....

I'm thinking of investing in a set of proper screwdrivers, mainly for clock repairs, rather than watches. (Eye sight not good enough for the really small stuff.)

What sort of price range should I be looking at?

Bergeon, very nice, but outside my price range.

Value, 5 pieces for less than £5, cannot be quality at that price.

Is there a quality, mid range set at a reasonable price?

What should I look for in a quality new screwdriver, tapered tip or parallel, replaceable, or resharpen-able tip?

Thanks

Bod

Link to comment
Share on other sites

A good set from a hardware shop will be fine. If you can try and get hold of some that will hold a slotted screw head in place. Comes in handy for fixing movements back in the case such as mantle strikes and chimes. A few Philips drivers and long handled box spanners come in handy.

Don’t forget good tools will last a lifetime if looked after.

box spanners.jpg

Link to comment
Share on other sites

For clock work the type of screwdrivers are not as important as they are for watches.

I just use a good quality set I bought from a local store years ago that had rotating tops, they are tapered and hardened so I can still sharpen them on a diamond stone if required.

The set of 5 probably cost me the equivalent of £15 to £20, unlike my watch screwdrivers that cost me £80.

Try looking in a local hardware of electronics shop

Link to comment
Share on other sites

Whilst working on a lot of German clocks i have noticed that the screws used on older clocks have narrow deeper slots than those found on modern screws they also tend to be rounded on the heads of the screws modern screw driver blades do not sit well in this type of screw so you will probably have to reshape the tips or if you can buy a set of thin blade screw drivers they sit better in the screw s and will not ride up out of the slot and slip.

Link to comment
Share on other sites

Don't forget the car boot sales and markets, you can find some nice screw drivers that may be old  however made with good steel and most have wooden handles (better for grip). If you see a foot long wooden handled screw driver with a nice thin tip get it as old long case movements have doomed thin slot bolt type that can be a bit stubborn to get out, however the extra length should crack it free. The less the taper on the driver end the better, they will sit better in the screw.

Link to comment
Share on other sites

Thanks for the replies.

I do have a good selection of engineering and woodwork screwdrivers, in most sizes.

It's as wls1971 states, German clock screws.  I have a couple of 400 day clocks with these deep narrow slotted screws, so I fear it will be down to the oil stone for re shaping tips.  I plan to look at the 1/4inch hex bits to see how much altering one of them would need.

Certainly £15-20 range for a watchmakers screwdriver set is well within budget.

 

Bod

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Hi guys I think that old hippy is correct, it opens the gates for china to manufacture aftermarket spare parts. considering that they already do work on behalf of the Swiss I guess this decision gives the a little more legitimacy to tool up and I am sure they will take advantage of the situation either with or without the blessing of the Swiss watch industry  Having read about the protectionist machinations of the Swiss in the history of Europe they were the only ones to get fat at everybody else’s expense. I think the outcome could have been guessed at but ,  fair play to Cousins UK for standing up to them.  Now the question,  will everybody boycott Swiss watches and Swatch, no way they will still fill their coffers.  Me I stick with the Japanese once renowned for cheap shitty watches who came good through industrial effort and don’t for get the Russians that most dismiss as low grade crap. Wouldn’t buy a swatch product ever how about you all.? a
    • Hold the crown when in winding position, move the click away from the crown wheel, and then while holding the crown let it slowly unwind. I recollect that you must remove the automatic device bridge first, but maybe I'm wrong. You can first try without removing the automatic device bridge.
    • nevenbekriev- You nailed it with your description of me and my reaction when the clock started ticking again. I am a newbie.  I love the sound and idea of mechanical clocks but the idea of owning one and trying to keep them running has never appealed to me. My wife bought this one and an antique German wall clock.  When I looked into having someone repair them for me, the universal response was "it's really expensive to work on them, you should just replace the movement". So, I had nothing to lose, I started researching them and opened them up. The wife is happy because she hears the sound of the clocks again. But I have gone down the "accuracy" rabbit hole. In the vertical position, the balance wheel was not floating. It was sitting on the bottom of the frame. I adjusted the lower spring collet and got it floating. It easily passed the 270 degree 3 to 5 minute oscillation test. It took 8 minutes for the wheel to completely stop moving.  I put it the unit back in the movement and checked the safety pin. It does not touch the safety roller anywhere in +/-270 degrees rotation from neutral position. But the amplitude of the rotation with the spring fully wound is weak based on what you are saying. It rotates +/-90 degrees from the neutral position.  No, I did not take the movement completely apart.  That seemed way outside my skill set at the time. There is a reason I became an electrical engineer and not a mechanical engineer. I am much more comfortable with moving electrons than tiny moving metal parts. Will I do it in the long run? Anything can happen. I don't seem to be able to let it go.
    • Isn't that the same guy who told Zelenskyy to escalate the war with Russia/Putin when they already had a peace deal? 2 years later and we have half a million young Ukranian boys dead. He doesn't seem very clever...
×
×
  • Create New...