Jump to content

Seiko 6309A Rotor Bearing?


Recommended Posts

I was contemplating the purchase of a Seiko 5 (online) and noticed in the pictures of the movement that it looks like the oscillating weight has been rubbing on the movement.  I assume the bearing the weight spins on will need replacement.  That bearing seems to be part of the frame it is attached to (according to the Seiko parts list) and not a separate piece.  My questions is, can this bearing be purchased and installed separately?  I am waiting to hear back from my local parts supplier to see if the bearing and frame assembly is even available.  The auto mechanic in me wants to remove the old bearing and install a new one in the original frame.  Here is a pic of the movement and what the complete replacement part (Seiko 193 601) looks like...

Cheers!

Roger

post-38-0-66015300-1417126068_thumb.pngpost-38-0-10684400-1417125975.jpg

  • Like 1
Link to comment
Share on other sites

Hi Roger,

 

I believe that part will be either hard to get from a supplier or very expensive considering this movement has been discontinued for many years. CousinsUK list it as obsolete (that's where I get my Seiko parts). You may have an option buying a donor movement from ebay or something...unless you find someone that has one around and want to donate/sell it to you. I usually prefer the 7S26/7S36 and newer movements to work on because of parts availability (mainly).

 

Have your thought about do a complete "transplant" and use a more recent Seiko substitute movement? On the other hand, it might just be a matter of tightening the rotor screw...I bought a Seiko once with the rotor almost loose inside and after tightening it worked perfectly.

Link to comment
Share on other sites

Thanks for all the helpful insight everyone!  I haven't bought the movement yet so will most likely pass on this one and try to find a Seiko 5 with a movement I can source parts for.  My local supplier also confirmed they no longer carry the rotor bearing assembly.  Clockboy, I will check Speedtimekollektion when I get home from work tonight for future reference - thank you.  Bobm12, I hadn't considered a transplant as I was hoping to buy a Seiko 5 that had a useable movement, but you certainly opened up some other interesting possibilities that will get me thinking in a new direction.

Have a great day!

Roger 

Link to comment
Share on other sites

Try

Speedtimekollektion.com they are a bit slow in delivery as the company is based in Spain but they do carry a lot of used old movement parts.

So I couldn't wait until tonight to check this site out clockboy, so I just went online and they do have the part! http://www.speedtimerkollektion.com/shop/index.php?cPath=32_97_116  I'll have to make some decisions now about the cost of the part with shipping and determine if I'll purchase the watch.  Have you purchased from them before clockboy?  Would they ensure the used part is actually serviceable?  Thanks again!

Roger 

Link to comment
Share on other sites

The preferred option is to fit a new part. But if not available there is no other option. After Swatch drop the hammer next year we might as well get used to this scenario. If it is for a customer then we will just have to be honest with the clients.

Edited by clockboy
Link to comment
Share on other sites



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Haha. You're just in a wicked mood today John 😅
    • Heres my watch of today, a Smith 13'" RY . My missus bought me this for this Valentines day a bargain 14.99 with a reduction, the seller has occasional 20% off offers now and then so it was about 15ish with delivery. I love Smiths and i love bulleye dials, this is my first one. The watch arrived non working as stated and i knew what was inside and what would be against me, but i enjoy a challenge, we dont expect a lot if anything from pin pallet movements. A balance pivot was broken and i didnt have another staff but i did have another RY with a battered dial so i robbed the balance and tweaked it around to make it work apart from that mostly just a good clean and relubrication. Keyless works are pretty rough by design and the crown is a bugger to get in and out with the dial on, the setting lever hits the dial before it releases it, so a little mod is needed to help that along. Major problem was the pins on the lever were quite worn which make the old tg have a snow storm fit. Its a similar read for most pin pallets, these were brass as was the escape wheel. But perseverance is me, i didn't change the pins but i did spend some time dressing and polishing the worn areas which improved the trace a lot with some straightish lines 😅 and a beat error of .5 . Not sure what the lift angle should be on these and i Wasn't in the mood to work it out and who believes timegraphers anyway, but at the default 52° it runs with 260ish full 210 after 24 hours dial down , the verticals rates were pretty much all over place. So lets just put it in it's superlight aluminium case and see what happens. Been wearing it now for 3 weeks and it's consistently losing around 1.5  minutes a week winding each morning i think pretty good for an old pin pallet watch. I just love this dial, thanks wifey heres my Valentine's gift for yer sweetie x
    • I have a PDF below that will help. The problem was the PDF wasn't designed for this purpose it was designed to tell you what size watch you  have. Then it doesn't take into account movements come conceivably in different thicknesses.   watch-ligne-size-chart.pdf
    • That would be something! Which brings me back to;  
    • you think you're going to sleep tonight you're not, you're going to ponder the question of what makes you think those of the right parts?  
×
×
  • Create New...