Jump to content

Best way of attack ?


Recommended Posts

Hi all, I have just dug out this elderly Favre Leuba twin power in the hope of reserecting it. It won't wind and is pretty gummed up and dirty. I have stripped it down and marked the springs in case they are different? As it's brass (I think) I am not sure as to what is the best way of cleaning it up ? I have taken photos and enclosed a few for your opinions as to how to go about it. Many thanks in advance.

IMG_20190413_220430.jpg

IMG_20190413_223351.jpg

IMG_20190413_220333.jpg

IMG_20190413_222407.jpg

IMG_20190413_220344.jpg

Link to comment
Share on other sites

I give it numeriois clean.

First, Soak in kerosene for several days and brush, kerosene is brass friendly for life, gives off bad oader, dosn,t evaporate but the lid on the jar,, then soak in paint thinner like  ten mins and brush after each soak,  Every part including the regulator arm is got to come off, I even brush the jewel housing. Keep repeating, three our four good brushing, soak - brush , this brings the shine back, no power drill to brush, just manual. tooth brush would be the roughtest brush you use on plates and bridges. You will start to see clean shiny parts perhaps after three or four clean.

Once looks clean, it is ready to go into your cleaning machine or general cleaning so to speak. This jewel is worth it.  

Best wishes.

 

 

 

 

 

  • Like 1
Link to comment
Share on other sites

7 hours ago, Nucejoe said:

I give it numeriois clean.

First, Soak in kerosene for several days and brush, kerosene is brass friendly for life, gives off bad oader, dosn,t evaporate but the lid on the jar,, then soak in paint thinner like  ten mins and brush after each soak,  Every part including the regulator arm is got to come off, I even brush the jewel housing. Keep repeating, three our four good brushing, soak - brush , this brings the shine back, no power drill to brush, just manual. tooth brush would be the roughtest brush you use on plates and bridges. You will start to see clean shiny parts perhaps after three or four clean.

Once looks clean, it is ready to go into your cleaning machine or general cleaning so to speak. This jewel is worth it.  

Best wishes.

 

 

 

 

 

Hi NuceJoe and thank you, watch parts sitting in a jar of petrol now ! Will follow your advice. Being brass I wasn't sure what to do and didn't want to ruin it through ignorance. Hopefully I can get it running again. Thanks for your best wishes. 

Link to comment
Share on other sites

Diesel fuel would work too, brushing in solvent helps. I use several solvent seperately, each will do some good.

Long time soak in paint thinner or carburator cleaner is harmful.

Paint brush is suitable for use on gears, pinions.

Shellack on pallet jewels and impulse are is susceptible to damage by solvents. 

I am talking ebauche and gears cleaning only. 

Picture shows Shock springs on cock and the mainplate diferent, should be the same.

 

 

 

  • Like 1
Link to comment
Share on other sites

12 hours ago, Johnnie said:

As it's brass (I think) I am not sure as to what is the best way of cleaning it up?

Virtually all watch plates are made of brass or similar alloy, then may be plated with different finishing.
Anyway petrol and alcohol based solvent are good to clean but will not make it shine the best. For that, if it matters to you, use ammonia based solutions, either off the shelf or you cold make your own with household products, in any case be careful to avoid high concentration or long baths.

  • Like 1
Link to comment
Share on other sites

Very true,

No matter how hign tech the plating on the base metal, there are pores or scratches, in the palting, through which solvents can penetrate to chew on the base metal. So one should be concerened with long term soaks with reactive solvents.

kerosene or Diesel fuel don,t chemically react with the base metal, it dose penetrate through the pores  slightly( no reaction), you just remove the penetrated( wetted surface) surface with brush, resoak , brush again, you are cleaning physically, ( no chem reaction) .Solvents chemically reactibe with the base metal, should only be use for  very short time and brushed and rinsed immediately.

You will see some clean by the first brushing, what news I have , is kerosene works. You are not limited to one clean, no harm with second or more clean, Once visibly clean, time for the final clean in your machine or whatever method you choose. 

I am staying with yoir thread, I don,t see why this service can be less than percect.

How dose the rest of the watch look? Dial, hands and case. Rare piece.

Regards 

 

  • Like 1
Link to comment
Share on other sites

Hi Joe, the case and crystal are good, the case back is ok but a little scratched, the dial is good but probably it has been refurbished. ??? If it has been refurbished it's been done far better than I could do it, so I'm not complaining. 

IMG_20190414_145855.jpg

  • Thanks 1
Link to comment
Share on other sites

5 hours ago, Nucejoe said:

Shellack on pallet jewels and impulse are is susceptible to damage by solvents. 

acetone and alcohol should also be avoided when cleaning pallet and roller jewels.

use naphtha (ronsonol lighter fluid) cheap and you dont have to syphon any out of your car lol

Edited by saswatch88
  • Like 2
Link to comment
Share on other sites

Done ! And running, it's 02.22 and my eyes are like organ stops. It turned out ok and I am pleased with it. Many thanks for all your help and advice. Ps, it's very good on petrol ! :D

IMG_20190415_020358.jpg

  • Like 2
  • Thanks 1
Link to comment
Share on other sites

5 hours ago, anilv said:

Great job cleaning it up.. do you have a case ring for it?

I have a similar watch and the case ring was cheap white plastic hacked up to fit. Works but not pleasant to look at.

Anilv

Hi Anilv, that is the only bad thing, when I got the watch the case ring fell out in three pieces. So will try and sort something out for it.

Link to comment
Share on other sites

12 minutes ago, Johnnie said:

that is the only bad thing, when I got the watch the case ring fell out in three pieces. So will try and sort something out for it.

That is when one really wants to have a small lathe. Someday...

  • Like 1
Link to comment
Share on other sites

18 minutes ago, jdm said:

That is when one really wants to have a small lathe. Someday...

That's for sure Jdm, At present I have "the basics" my next three things have GOT to be are Mark's course, a timegrapher, and some sort of parts washer, my mind boggles at all the different tools required. The more I learn from this fantastic forum the more tools I need. Being probably one of the least knowledgeable people on this forum my head spins at times. I freely admit when I joined that I destroyed many cheap eBay purchases that have become my parts department :D but have been successful in rebuilding four Seiko's and that's given me enough pleasure to get more serious. (Now addicted) 

  • Like 1
Link to comment
Share on other sites

1 hour ago, vinn3 said:

   i would place a lathe at the top of the list of things to buy to work on watches.  vin

Indeed so, if I were more knowledgeable Vin, at present I am an enthusiastic tinkerer, so Marks complete course must come first. Aim to subscribe in the within next few weeks !

  • Like 1
Link to comment
Share on other sites

16 hours ago, Johnnie said:

I have just noticed on the left of column there is "a tick, a triangle, and a zero" ? What is that about ? 

The triangle is to vote up an answer.

In the topic index there is a 'pinned' post explaining the Vote Up function.

Anilv

  • Like 1
  • Thanks 1
Link to comment
Share on other sites

16 hours ago, Asmobrat said:

Well... I tried contact cleaner and rinsed with blade oil on Seiko 6309... It worked well... Especially the rust residues...

 Contact Cleaner  might  be good  if you remove the balance assembly first.  vin

  • Like 1
Link to comment
Share on other sites



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Looks that way, if it had any amount of significant jewel count it would say so on the dial.    Looks that way, if it had any amount of significant jewel count it would say so on the dial.  Same answer as Mike regarding the dial, its often just a slapped on name of a retailer but i thought you were way above this understanding Pete ?
    • Light naptha is what you need to be looking for. The carbon to hydrogen ratio is high with heavy naptha, it doesn't evaporate as well as light naptha and is prone to leaving more residue. Try tom's suggestion of the mirror test.
    • Its a big item Michael and a lot that could go wrong with the process of getting it to its new location. I once helped install one of these units into a conservatory that i had built. It was big and bloody heavy and took six of us to get it in safely. If you have sliding doors and you need to remove the whole frame then that may or may not go well. But i would advise getting a professional in if you have little knowledge on the installation of them. The glazing of the doors could well be 6mm laminated glass which again will be heavy very heavy if the glazing units are big. The glass would also need to be set up and packed correctly to open the doors properly more so if they are unframed and the sliders are upvc. Seems a shame but if no one is biting and that may be due to having no warranty i guess the only takers might be someone that installs them for a living and knows how to repair. If its fibreglass just be careful, i sometimes have to cut fibreglass baths out and they are nasty to work with . Thick gloves are definitely recommended,  not fun picking out fibreglass spells two days later that have started to go septic. Good luck with it all matey.
    • I don’t know anything about this product, however assuming you have it if you put a drop on a mirror or piece of glass lying flat on a table and leave it to evaporate if it leaves any sort of residue it is not really suitable for watch part cleaning.   Tom
    • Well I put the spa on Gumtree (selling service) to try and sell it as it only needs a recirc pump to get it going. However, it weighs circa 250kg, so there's 4 fairly strong guys, and I would have to remove the sliding door in the room completely to be able to get it out, as well as clearing out a multitude of potted plants and the Alfresco outdoor setting to be able to get it out. Then move nearly everything in the back of the garage to be able to push it through to the front of the house. I would also need to hire furniture skates to be able to shift it around as carrying it is out of the question. Then someone would need a trailer to get it to their place as you won't get it on the back of a ute. So, the only answer is, out with the reciprocating saw and cut it all up into manageable pieces. Crying shame as it is in really good nick. I was only asking $1,500 and only got two bites, but it would only take something to go wrong with removing the sliding door etc that everything I make on the sale could go out the door on repairs etc. It would have been nice to be able to turn it into tools etc, but que sera sera. I don't know about the rest of the world, but there just seems to be very little interest from people wanting to buy things secondhand.  
×
×
  • Create New...