Jump to content

Plot 2409 part 502 can anyone help?

ftwizard
 Share

Recommended Posts

ftwizard WRT Addict

ftwizard

Posted
Posted

I volunteered to fix a friends watch, sentimental value, inherited from deceased uncle and all that, and of course at the first opportunity, I pinged the setting lever plunger across the room. I've searched everywhere, to no avail.

So if anyone has the part or a spare movement they can part with, I would be most grateful.

 

Cheers.

Link to comment
Share on other sites
ftwizard WRT Addict

ftwizard

Posted
  • Author
Posted
1 hour ago, rogart63 said:

Almost think i have but someone living closer to you maybe have one ? If not i can have a look. 

Thanks for your help. I know you've helped me out in the past, and it's very much appreciated.

  • Like 1
Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • ManSkirtBrew
      1972 Bulova President "E" Sea King 11ACACB movement

      By ManSkirtBrew · Posted

      Oh nice. I have a similar wedge style stump for my staking tool, so I'll give that a shot. Thanks!
    • joelcarvajal
      Gamblin Gamsol for cleaning?

      By joelcarvajal · Posted

      Thank you all for the replies!  Very informative! True enough, the Gamsol took some time to evaporate and does leave a residue. So not all naphtha are created equal!  Need to find alternatives then. i was able to try Hexane recommended by Alex and it seems great.  I wonder what the cons are?
    • GuyMontag
      1972 Bulova President "E" Sea King 11ACACB movement

      By GuyMontag · Posted

      Yeah, I saw that in the tech sheet but I don't see how it can be adequately cleaned with the friction pinion still in place. I've accidentally pulled the arbor right out of the wheel once when I used a presto tool to try and remove it. Mark shows how he does it with the Platax tool. Those are a little too pricey for me so I got one of these from Aliexpress and I just push down on the arbor with the end of my brass tweezers. That usually gets it most of the way out and then I just grab the wheel with one hand the and the friction pinion with the other and gently rotate them until it pops off. Probably not the best way but it's seemed to work for me so far.    
    • Zedster
      Movement inserted from crytal side

      By Zedster · Posted

      Thanks, Jon Sounds like a plan. Obviously I'll have the face on so do you think gripping with the holder will create any problems, but I will check in the morning to see how feasible it is but I assume it only needs to be lightly held. As for holding the movement instead of the holder won't be possible in this scenario as one hand will be puling on the stem while the other pushes the spring down. That was my initial concern is how the hell can I do this with only one pair of hands. All the other times I've had to remove the stem hasn't been a problem, apart from the force required to release the stem from the setting lever, but now I need to fit the face and hands its sent me into panic mode. If it had the screw type release things would be a lot simpler but that's life 😀   Another thing I will need to consider is once the dial and hands are fitted and the movement is sitting in the case I will need to turn it over to put the case screws in. I saw a vid on Wristwatch revival where he lightly fitted the crystal and bezel so he could turn it over, is this the only option or is there another method?      
    • nevenbekriev
      Main spring

      By nevenbekriev · Posted

      Hi Jon, do You think that relation spring torque - amplitude is linear? I would rather guess that the amplitude should be proportional to the square of the torque. I had once idea to check it, but still haven't.
×
×
  • Create New...