Jump to content

Help Required to remove crown stem

Scott
 Share

Recommended Posts

Scott New Member

Scott

Posted
Posted

This is an old rip curl watch with tide indicator. I’ve owned it for at least 22 years. My daughter recently found it and decided she likes it. The inside of the glass and face appear a bit fogged, so basically want to remove the crown to access this. Also any tips to help make it water resistant around the crown and gasket would be handy. It was WR to 10atm when new. 

8931716E-8A9C-417A-B93D-49CCBAB97262.jpeg

Link to comment
Share on other sites
watchweasol Distinguished Member

watchweasol

Posted
Posted

Hi This is a france eubauches movement   (technotime) there should be a calibre number on the movement for identification purposes.   Inside the crown is usually a small neoprene/rubber ring gasket, replacing this  along with the case gasket after treating them with silicone grease just a smear  and re fitting will improve its its capability to shed water. To remove the stem on these i think it was pull out the stem and a small tag swings out press this tag down and draw out the stem.  If you can find the calibre number on the movement it would be a great help.

  • Like 1
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Jon
      What are these Seitz B-Jewels?

      By Jon · Posted

      I picked up a similar amount of these jewels some years ago in a watch and clock fair. Every now and then they come in handy. This week I've got a rubbed in bombe jewel in the balance cock that is cracked and needs replacing. Very handy to have a vintage assortment of these type of jewels!
    • Stirky
      Diagram for 6497 motion works

      By Stirky · Posted

      Thanks Jon.
    • Jon
      Diagram for 6497 motion works

      By Jon · Posted

      Great diagram with the teeth and pinion count. Simple way to reduce the speed of the hour wheel by the 12:1 minute wheel. Genius and yet so simple. Always good to reinforce the principal by what you have done in your drawing. Keep doing that. I had a drawing on my wall for years showing me this which is very similar to the drawing you have done. Here's a formula to work out the beats per hour of a watch movement. The movement's BPH is dictated by the wheel teeth and pinion count and the hairspring being vibrated to the correct BPH by finding the pinning up point on the hairspring using a vibrating tool.  The reason in the formula there is X2 on the top line is because there are two pallet stones.
    • DDean
      Incabloc Lyre Spring & Low Earth Orbit

      By DDean · Posted

      So I just wanted to say "thank you" again.  The angle is the key bit it seems and yes, it did basically just fall, or float, back into position when I got it lined up just right. I had meant to add that now that I see how it goes in, I totally see how it came out in the first place, and that whomever cloned the original movement didn't pay much attention to the fine details around the setting or how it interfaces with the balance cock or the "rings" on the regulator and/or stud carrier arms.
    • transporter
      Commando special

      By transporter · Posted

      Well I’ve never seen the make before and cannot find any info, I haven’t got it just yet it’s been left to me among a 1970’s sea master and a mid size yeoman. But if anyone has any information on this one please feel free to enlighten me, many thanks 
×
×
  • Create New...