Jump to content

Third wheel pinion removal


Recommended Posts

best way is to knock it out using a staking set the same way you would remove a balance staff.

you can try and use a canon pinion/hand remover tool if you can get the lever under it. but you have to place the the wheel on a staking block  with smallest hole you can fit the top pivot in. but these are friction fit but these watches are old so some penetrating oil may be needed for this process.

if you have a spare wheel why not just replace the whole wheel? what size is the movement?

Edited by saswatch88
Link to comment
Share on other sites

I agree with replacing the whole wheel (if it's the same). As for getting the wheel off, some wheels are friction fit to the pinion arbor, some have a hub which is friction fit to the arbor (think of the hub as part of the wheel), but the traditional way of attaching would be staked to the pinion leaves. Here the pinion is turned down a bit in diameter, and a rivet formed, the wheel is staked on, then riveted. The leaves bite into the wheel a bit and that along with the riveting makes a very secure hold.

It kind of looks like you have the latter. If you simply knock the pinion out there's a good chance of distorting the wheel, or enlarging the hole, or possibly breaking a pinion leaf. Best is to turn away some of the rivet before knocking it out. Then in the lathe, slightly chamfer the end of the leaves where they enter the wheel- you'll see that they are slightly bulged from being riveted before, and recut the rivet (don't shorten the seat length, just make the rivet "sharp" again). The little chamfer on the pinion leaves will help you get the wheel on concentrically- also you want to get the leaves in the slots already formed by the previous pinion. The seat length will be slightly shorter than original regardless, so you can also chamfer the hole in the wheel slightly so that the rivet has room to be staked over.

Link to comment
Share on other sites

19 minutes ago, nickelsilver said:

I agree with replacing the whole wheel (if it's the same). As for getting the wheel off, some wheels are friction fit to the pinion arbor, some have a hub which is friction fit to the arbor (think of the hub as part of the wheel), but the traditional way of attaching would be staked to the pinion leaves. Here the pinion is turned down a bit in diameter, and a rivet formed, the wheel is staked on, then riveted. The leaves bite into the wheel a bit and that along with the riveting makes a very secure hold.

It kind of looks like you have the latter. If you simply knock the pinion out there's a good chance of distorting the wheel, or enlarging the hole, or possibly breaking a pinion leaf. Best is to turn away some of the rivet before knocking it out. Then in the lathe, slightly chamfer the end of the leaves where they enter the wheel- you'll see that they are slightly bulged from being riveted before, and recut the rivet (don't shorten the seat length, just make the rivet "sharp" again). The little chamfer on the pinion leaves will help you get the wheel on concentrically- also you want to get the leaves in the slots already formed by the previous pinion. The seat length will be slightly shorter than original regardless, so you can also chamfer the hole in the wheel slightly so that the rivet has room to be staked over.

I agree with riveted pinions, they are risky to punch same as riveted staffs. but 3rd wheel is not riveted on these waltham pocket watch movements, only the center wheel is, i know because i work on these a lot, sometimes i even get some waltham/elgin that have loose pinions on a few occasions pinions have actually fallen out  of the wheel. and the leaves are friction fit to the pinion. so it should be able to come off without punching out the entire pinion. maybe he should try penetrating oil and try gently twisting it off before hitting up the stakes. i would like to know the size of the movement though i think 12s 18s may be riveted not sure but iam sure 6s and down isnt

Edited by saswatch88
Link to comment
Share on other sites

I agree with riveted pinions, they are risky to punch same as riveted staffs. but 3rd wheel is not riveted on these waltham pocket watch movements, only the center wheel is, i know because i work on these a lot, sometimes i even get some waltham/elgin that have loose pinions on a few occasions pinions have actually fallen out  of the wheel. and the leaves are friction fit to the pinion. so it should be able to come off without punching out the entire pinion. maybe he should try penetrating oil and try gently twisting it off before hitting up the stakes. i would like to know the size of the movement though i think 12s 18s may be riveted not sure but iam sure 6s and down isnt

So, for the third wheel, I actually need to take a good pinion and replace the bad pinion on the original. The wheel on the original is ok. Is the pinion really part of the shaft as a single piece of metal. I know the center wheel had a safety pinion that screw off...but not sure I can actually remove the 3rd wheel pinion/gear.


Sent from my iPhone using Tapatalk Pro
Link to comment
Share on other sites

2 hours ago, jdrichard said:


So, for the third wheel, I actually need to take a good pinion and replace the bad pinion on the original. The wheel on the original is ok. Is the pinion really part of the shaft as a single piece of metal. I know the center wheel had a safety pinion that screw off...but not sure I can actually remove the 3rd wheel pinion/gear.


Sent from my iPhone using Tapatalk Pro

you should be able to remove the pinion from the shaft, but it might be hard to friction fit the new one. so not sure whats better to remove pinion or entire shaft because normally i dont do this i just replace the wheel since i have a ton of spare parts. any reason why you cant just replace the whole wheel? i may have a spare if you dont have one

Link to comment
Share on other sites

you should be able to remove the pinion from the shaft, but it might be hard to friction fit the new one. so not sure whats better to remove pinion or entire shaft because normally i dont do this i just replace the wheel since i have a ton of spare parts. any reason why you cant just replace the whole wheel? i may have a spare if you dont have one

One of the pinion leaf is broken. And the other gear shaft is too short.


Sent from my iPhone using Tapatalk Pro
Link to comment
Share on other sites


So there is no robbing a single pinion. Could make one with my Lathe??


Sent from my iPhone using Tapatalk Pro
Well, you may be able to graft the good wheel on the good pinion.

To make a pinion is no small feat, first of all you need a milling attachment and a way to divide, then you need the appropriate cutter or the means to make one.
Link to comment
Share on other sites

2 hours ago, nickelsilver said:

The pinion and arbor are one piece. Only the center pinion, on certain American calibers, was a separate piece.

they look like to pieces in he picture, doesnt look like the pinion was machined out of the same stock as the shaft, i know have had few movements that where loose or maybe it was the whole shaft that was loose and just thought it was the pinion, and yes the center wheel pinion is 100% friction fit that i know for sure, but only on 3/0s and up i believe

JD you can buy a spare movement very cheap on ebay, prob less than $10, just save yourself the headache and get a new wheel man!

Edited by saswatch88
Link to comment
Share on other sites

Update: Put original 3rd wheel in Lathe and graved down the pinion leaves and arbor down to an acceptable diameter.4dbf46d71830211bdd9753d3716b40cd.jpg
Next plan is to get the sacrifice pinion on its arbor/shaft and drill a hole in it the same diameter as the one I cleaned up.


Sent from my iPhone using Tapatalk Pro

Link to comment
Share on other sites

wow nice job! see iam lazy i would have just replaced the wheel, plus i dont have a lathe so that too

Funny. I like the challenge, plus it would cost 20 bucks for the new part and my labour is free.


Sent from my iPhone using Tapatalk Pro
Link to comment
Share on other sites

Wow that was really great to watch, excellent job.. Is the watch back together now? Which lathe do you have if you don't mind me asking?

The watch will be together today for a test, then I still need to strip and clean it. I have 5 lathes with countershafts, on Borel Stands and 5 conventional desk mount. All vintage. The Lathe I used was a Boley and Lienen.75a95480f5b3f3b67586d15a75de8940.jpgb720e7e7242118dbfcbfd27cd64aadee.jpg
With a collet holding Micrometer tailstock.


Sent from my iPhone using Tapatalk Pro
Link to comment
Share on other sites

Wow that was really great to watch, excellent job.. Is the watch back together now? Which lathe do you have if you don't mind me asking?

37b4364a51b65678ba4cb87b5692188b.jpgfd2827bebd4549b0a88c004dbced8003.jpge15c34ec7b435c043891af506e5aadbe.jpg29a46d9c70f8663f9bdd5345a338eaca.jpg8b5646330e71da06e3423cf40030195d.jpg967a7793abdcb3f45c4d5cf7d51eec4c.jpg
All done:
Done.
1) Made New Balance Staff
2) replace center wheel
3) made/replaced 3rd Wheel pinion
4) Replaced Balance Cock Top Jewel
5) Cleaned and reassembled.



Sent from my iPhone using Tapatalk Pro
Link to comment
Share on other sites

  • 1 month later...
Making a video at the moment, however, the transplant was successful.64d742dda163b682f3021b89823920b1.jpg&key=2efcad752914d1289b48870b4db8d4cb10114ead50497c7f9a918abb4fd9085d97fe9dcd9f0d53397882e6a996370e1b.jpg&key=6022d8de356b1d40a86eb882de568a6666c20365e1a27c618579da8e1a679eeddb8cf869790f1faa09dd0e9a78a383f7.jpg&key=64d5f7ed571a2f951d84153bfdfcd8327057f41d77c8c63f10e2cec63122c23b4b94dbfc59e8a2744ff2561358862d79.jpg&key=857ade43ca9dabeb76c9890f5003e91ea49210c5881831138f578c1d0f67ca8ca13f736733afd5827ab78da9c1125d12.jpg&key=75445574cc45c1e65185006459e8c32c648fffa61a637cf787739da184771015


Sent from my iPhone using Tapatalk Pro

So after all this work, I had to re-glue the pinion back on as the pressure from the center wheel caused to to break the glue seal. I was successful the second time by roughing up the wheel a bit, where the pinion touches is, so there would be more material for the glue to grab. Next time, however I will make sure I get a friction fit and don’t take so much material off.


Sent from my iPhone using Tapatalk Pro
Link to comment
Share on other sites



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • that band is old as stated, there is a kit that pops up from time to time on selling sites for the repair of these type bands, some of this type are adjustable on a few links, one adjustable type allows you to align the round opening in the expansion slit [like yours] with the rivet to separate, but if yours won't come out then the rivet head is too big and will have to be done with some rivet removal and replacement, I suppose if you could make/optain the correct rivets that one could alter the said band, the tops/caps do lift off after raising the tabs....  
    • This is a watch from a friend who sent it to a neighborhood watchmaker for a battery change. It came back with the watch stem in a ziplock bag and the dial skewed 20°. The watchmaker told him that the stem was faulty and the watch cannot be repaired. I opened up the watch and found that one dial foot was broken off and still stuck in the movement, while the other was bent until it was flat against the dial. The stem could be inserted but it couldn't be pulled out to quickset and time adjusting positions. I did a full disassemble, cleaned and oiled the movement. But when it put in the battery, the second hand runs super fast. Like it gains 30 mins every hour. Any advice on fixing this problem? TIA.
    • I determined that the balance staff is rotating, not the roller table, so my second attempt at riveting was unsuccessful. I have ordered a new balance staff and will take measurements when it arrives. The balance staff i originally ordered (and now reordered) was specified as: Replacement balance staff: (A. Schild Caliber 984 1002 1021 1124 Original Balance Staff Part 723) so it should be correct. Measurements: (see pic below for terminology) xxxyy is a place holder until the new balance staff arrives. Lower pivot: Old - .08 mm New - xxxyy Lower pivot to balance seat: Old - 1.53 mm New - xxxyy Roller shoulder: Old - .42 mm New - xxxyy Hub: Old - xxxyy New - xxxyy Balance shoulder: Old - .86 mm New - xxxyy Collet shoulder: Old - .56 mm New - xxxyy Upper pivot: Old - broken New - xxxyy
    • Hello and welcome from Leeds.  We're here to help. 
    • I was just about to adk that, probably they have unnecessary waiting lists to make their watches appear more exclusive than they actually are.
×
×
  • Create New...