Jump to content

A nice carriage clock.


oldhippy

Recommended Posts

The only slightly odd thing I can see is that the dial markings look slightly misplaced.

If the diameter of the seconds markings were a few millimeters smaller, it would make the face look slightly better balanced. As it is, they appear to take the design too high up on the face.

Other than that slight quirk, it looks, to my untrained eye, pretty clean and well preserved (or restored).

Would I prefer the carriage clock, or another 1,424 3/4 members of the 404 club.. That's a tough choice. :P

I suspect my wife would take the carriage clock, for the practical reason that it would take up a lot less space. :biggrin:

Edited by AndyHull
Link to comment
Share on other sites

On 4/1/2019 at 3:53 AM, AndyHull said:

Other than that slight quirk, it looks, to my untrained eye, pretty clean and well preserved (or restored).

If you have a look at the photo with the back door open, they could have redone the bluing of the screws and recut at least one of them. For that kind of money you want it Museum quality.

Link to comment
Share on other sites

The case style is not common but they do turn up at a rate of 3 or four a year , the biggest difference to price depends on the escapement fitted to the clock one sold at Dreweatts auction house newbury described as follows :

A fine French gilt brass carriage clock Japy Freres, Beaucourt and Paris, circa 1860 The eight-day two train bell striking movement with gilt platform lever escapement regulated by unusual three-arm sprung monometallic balance applied with three axe-head shaped blued steel projections to rim, the backplate with small bell over stamped central oval trademark JAPY FRERES & CIE, EXPOSITION 1855, GRANDE MED. D HONNEUR.

That fetched £1,000 on the 20 sep 2017

Another with the same case but fitted with a engraved detent chronometer platform and center seconds sold for £1,600 in 2015

I would say the one being sold on ebay would fetch £1,000 to £1,500 at auction

Link to comment
Share on other sites

4 hours ago, Bod said:

Bit of a price difference.

What would you expect the auction estimate to be?

 

Bod

It all depends who is after it. If the competition is high, it could run away and fetch a very high price. The case, platform, and maker will play a big part in price. I notice the screws have been mentioned, it makes no difference they can easily be tidied up and re-blued. The asking price on the original post was ridicules. I am out of touch with the market and prices these days. At a guess £2000 plus.     

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • In the meantime whilst awaiting a better plan, please drop me a quick hello on my email. 
    • I looked at it like this, I've built a lot of stuff in my time, building structures and furniture,those are my creations and they will still be here way way after I'm gone. Traditional watchmakers felt the need to pass their knowledge on, ideas that they created . I assume with them as it is with me, leaving their mark on the earth, a way of being remembered. This creation of Mark's has brought thousands of people together to pass their knowledge around,  ideas that will continue to be used for lifetimes. Ideas that should continue to be procured. If for whatever reason the forum ceased to exist, not quite like Ranfft's, that didn't disappear but much less usable. Then that is sad, such a massive loss of communication between good people and a wealth of knowledge lost. There should be something in place for when that happens which could be next week, next year or in 10 years. Might not be a topical subject for a lot of folk or boardering on controversy, i did say i talk about stuff other people dont. But if you dont talk about it and something happens then you've lost it and you ain't gonna fix it .
    • I've remained silent on this thread, and at the risk of upsetting everyone, the thing that worries me the most the the apparent absence of Mark. The moderators do a great job and the members also pitch in, and the site seems to run itself, but it is a concern for the future of this forum when the owner is absent for all intents and purposes. Like many of the comments above I would hate to log in one day and things be closed down as I rely on this site for ideas and knowledge and also cheer me up. maybe the Moderators could reach out to him, assuming he does not read this thread, and express our concerns and let us know the plans going forward? some kind of WRT ark
    • That was the exact reason for me starting this thread watchie. Still we haven't worked out how the regulars are going to hook up if it goes tits up. I honestly think something should be arranged to stay in contact, we all help each other so much. 
    • Yeah ive watched that a few times before,  i couldnt find my old school dividers to scribe it up 😅 Yep thats the guy i bought a roll from . Thanks Nicklesilver that answers that perfectly and more or less what i thought an experiment over time would prove . The jumper arm is quite thick along its length, i left it that way intentionally, i thought the original was probably very thin, i didnt see that it was already missing. Setting isn't particularly stiff as such just positive, i still need to take it out and polish where it mates with the stem release. 
×
×
  • Create New...