Jump to content

grease the gasket?

phydaux

By phydaux
in Watch Repairs Help & Advice

 Share

Recommended Posts

phydaux Watch Enthusiast

phydaux

Posted
Posted

I am in the process of casing up a 2824 clone movement.  The case I am using has a screw down crown & case back.  I have a question regarding the case back gasket.

Once I get the case back gasket in place and am ready to screw on the case back, should I first apply some sort of grease to the gasket?  For some reason I think that is something I'm suppose to do, but I honestly don't know why I think that.

Link to comment
Share on other sites
watchweasol Distinguished Member

watchweasol

Posted
Posted

Hi      the answer is yes greasing the gasket makes a water/moisture tight seal keeping the water/ moisture out. all it needs is a smear on the gasket.  there are recommended greases for the job I use silicone grease rubbed on the fingers to warm it up then put it on the gasket had no problems with that over many years.

  • Like 1
Link to comment
Share on other sites
jdrichard Distinguished Member

jdrichard

Posted
Posted
Hi      the answer is yes greasing the gasket makes a water/moisture tight seal keeping the water/ moisture out. all it needs is a smear on the gasket.  there are recommended greases for the job I use silicone grease rubbed on the fingers to warm it up then put it on the gasket had no problems with that over many years.

I do the same with Seiko silicone grease


Sent from my iPhone using Tapatalk Pro
Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • DDean
      Incabloc Lyre Spring & Low Earth Orbit

      By DDean · Posted

      Just a note for those who come searching for information on this topic in the future.  I did eventually find the Mark's video on how to replace these springs, as someone observed, he does in fact make the replacement look easy.  (It actually is relatively easy once you have the knack of it.) If you're enrolled in one of Mark's online courses, the demonstration of how to replace this spring is in the Bonus Videos section of his course site, and is called "C2B1 – Sea-Gull Style Shock Springs".
    • RichardHarris123
      Setting lever spring

      By RichardHarris123 · Posted

      If the metal was twice as thick, it wouldn't snap so easily.  The thickness is governed by the space available so you can't use thicker metal.  If you glued two pieces together, the likelihood of snapping would be reduced.  That's my theory anyway, could be wrong. 
    • JohnR725
      Pocket watch escape wh

      By JohnR725 · Posted

      there are various approaches to learning watch repair. A lot of people want to jump right in and every single watches something to be repaired restored. But other times like this it's disposable it's here for you to learn and when you're through learning you throw it away. yes you definitely should try this you have a learning movement you need to learn and the best way to learn is by doing something.
    • nevenbekriev
      Pocket watch escape wh

      By nevenbekriev · Posted

      Sorry, the friction will be so great that the wheel will barely turn, if the movement will start at all, the amplitude will be verry lo.
    • Bonefixer
      Pocket watch escape wh

      By Bonefixer · Posted

      If I can’t re-pivot the wheel, the logical thing to do is to descend the pivot hole.  Plan is to either stick a suitably sized hole jewel (from a barrel bridge or something) or fashion a blob of epoxy on the underside of the escape wheel cock so the wheel sits on its one pivot on the base plate and the staff with the broken off pivot (which I’ll polish as best as I can) becomes the upper pivot. As long as it doesn’t foul the 4th wheel it should work? I know it’s a bodge job, and if this were a rare movement, or belonged to someone else I would not do this. I’m just interested to see if I can get the thing to run. 
×
×
  • Create New...