Jump to content

Pulling the stem Harley Ronda


Recommended Posts

Look closely near the stem and you may see a little dot on a part or an arrow pointing at something to press down which will release the stem.

You may need to put the stem in the setting position for it to be visible.

Link to comment
Share on other sites

Look closely near the stem and you may see a little dot on a part or an arrow pointing at something to press down which will release the stem.
You may need to put the stem in the setting position for it to be visible.

I tried many times using the eye loop but was unable to see any dot or arrow!!


Sent from my iPhone using Tapatalk
Link to comment
Share on other sites

Remove the ring around the movement so you may see the watch.:lol:

Seriously,   I got a suspecious feeling you just might find a lever or something on the side near the stem. If nothing found, I unscrew the crown and slide the movement out.

Regards

Link to comment
Share on other sites

Hi A.  Remove the ring around the movement so you may see the watch.:lol:

Seriously,   I got a suspecious feeling you just might find a lever or something on the side near the stem. If nothing found, I unscrew the crown and slide the movement out.

My apology Tmuir didn,t mean to barge in like this. Wont be repeated.

Regards

Link to comment
Share on other sites

Hi A.  Remove the ring around the movement so you may see the watch.:lol:
Seriously,   I got a suspecious feeling you just might find a lever or something on the side near the stem. If nothing found, I unscrew the crown and slide the movement out.
My apology Tmuir didn,t mean to barge in like this. Wont be repeated.
Regards

No need to apologize, and thank for the advice!
Will remove the plastic ring and see if I can find a lever
But didn’t get what you mean by unscrewing the crown and remove the movement!


Sent from my iPhone using Tapatalk
Link to comment
Share on other sites

Just grab the stem with  long- nose pliers and unscrew the crown off of the stem. This is prefered approach if you really don,t need to remove the stem and just want to get the movement out.

Thanks I’ll do that and see


Sent from my iPhone using Tapatalk
Link to comment
Share on other sites

23 minutes ago, watchweasol said:

Hi    This might be of some use   ronda tech sheet,  as I recall you pull out the stem to set position 

       and you see a small lever poking out press this down and remove stem.

571_Ronda1062,1063,1064,1069NEW.pdf

:Bravo:    I remeber now, got a miyota with the similair set lever, stem comes out like you said. . 

Link to comment
Share on other sites

Hi    This might be of some use   ronda tech sheet,  as I recall you pull out the stem to set position 
       and you see a small lever poking out press this down and remove stem.
571_Ronda1062,1063,1064,1069NEW.pdf

I pulled the crown but couldn’t see the stem.
I think it’s better to take the watch to a Jeweller to avoid damaging the movement
Thank you all for the help


Sent from my iPhone using Tapatalk
Link to comment
Share on other sites

  • 1 year later...

Sorry,  I know this is way to late but it might be useful for future reference for someone else. 

In almost all of the pictures above the release pin is clearly visible but I've attached a photo of one of my own watches with a circle around it. 

Be sure the stem is not pulled out into gear (hands or date) push the release pin gently down with anything small enough to fit the hole while holding the crown, you can feel the release point, and pull it out.

When reinserting, be sure to push the release pin as well, I'm not sure if there are other stems out there, but mine isn't tapered so you can't just push it in on its own

 

20200917_085301.jpg

Link to comment
Share on other sites



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • I have it, so until we get a lunch one day , nearly everyday is with my mum at the moment.
    • In the meantime whilst awaiting a better plan, please drop me a quick hello on my email. 
    • I looked at it like this, I've built a lot of stuff in my time, building structures and furniture,those are my creations and they will still be here way way after I'm gone. Traditional watchmakers felt the need to pass their knowledge on, ideas that they created . I assume with them as it is with me, leaving their mark on the earth, a way of being remembered. This creation of Mark's has brought thousands of people together to pass their knowledge around,  ideas that will continue to be used for lifetimes. Ideas that should continue to be procured. If for whatever reason the forum ceased to exist, not quite like Ranfft's, that didn't disappear but much less usable. Then that is sad, such a massive loss of communication between good people and a wealth of knowledge lost. There should be something in place for when that happens which could be next week, next year or in 10 years. Might not be a topical subject for a lot of folk or boardering on controversy, i did say i talk about stuff other people dont. But if you dont talk about it and something happens then you've lost it and you ain't gonna fix it .
    • I've remained silent on this thread, and at the risk of upsetting everyone, the thing that worries me the most the the apparent absence of Mark. The moderators do a great job and the members also pitch in, and the site seems to run itself, but it is a concern for the future of this forum when the owner is absent for all intents and purposes. Like many of the comments above I would hate to log in one day and things be closed down as I rely on this site for ideas and knowledge and also cheer me up. maybe the Moderators could reach out to him, assuming he does not read this thread, and express our concerns and let us know the plans going forward? some kind of WRT ark
    • That was the exact reason for me starting this thread watchie. Still we haven't worked out how the regulars are going to hook up if it goes tits up. I honestly think something should be arranged to stay in contact, we all help each other so much. 
×
×
  • Create New...