Jump to content

An aluminium-cased longcase clock?


2131tom

Recommended Posts

My reaction was: 'It shouldn't be allowed' but am I being a traditionalist stick-in-the-mud?  

See:  http://www.ebay.co.uk/itm/323699767134?ViewItem=&item=323699767134

What's your thoughts?  The clock is still being produced and does have a high-end price.  No disrespect intended to the maker, but I'm not sure about the value of the Hermle movement  

Aluminium longcase.jpg

Link to comment
Share on other sites

I gasp in horror at this. Hermle tells me right away its modern and the movements are not that good. In 30 years it will need to be replaced. To me it is not a Longcase clock. It is a modern case that is supposed to resemble a Longcase clock. At that price, you could get yourself a genuine antique Longcase.

Link to comment
Share on other sites

Putting my antique restorers hat on, I can see a few issues as time goes on, the case looks to be solid timer  that will warp over time due to the aluminium cladding that would have to have been glued to the timber, therefore the timber not being able to expand and contract due to moisture content in the air, most likely the aluminium veneer will come off the timber and show bubbles on such a highly polished surface. The movement, well have a look at this 20 year old Hermlie movement, mind you it has not seen a service in that time, also the cheap construction of the way they attached the seconds hand, how are you supposed to hit in the bush without bending the small plate, well I used engineers clamps to push it in, however if it was held by a few screws you could have taken it off and hit the bush in on the flat.

KeithsClock2.jpg.5b52853e530d33b5c23d11eca8fb0e33.jpg

KeithsClock3.jpg.8450c7672664288739c4479f953e806a.jpg

 

Link to comment
Share on other sites

I had another look at the case, it is doubled skinned so the timber can breath, I just hope the inner skin is not glued to the drawer unit as it will surly crack/split, it should be slot screwed to allow for the expansion and contraction

Link to comment
Share on other sites

Its a over priced piece of tat, designed to part the gullible of large amounts of cash, it is nigh on valueless as the seller will find out, he could list it till the end of time at that price and it will not sell, if this came up at auction it would fetch £100 -£200 at best purely because some will find it decorative.

To part with over £13,000 when new really does prove the old adage that some people do have more money than sense.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Heres my watch of today, a Smith 13'" RY . My missus bought me this for this Valentines day a bargain 14.99 with a reduction, the seller has occasional 20% off offers now and then so it was about 15ish with delivery. I love Smiths and i love bulleye dials, this is my first one. The watch arrived non working as stated and i knew what was inside and what would be against me, but i enjoy a challenge, we dont expect a lot if anything from pin pallet movements. A balance pivot was broken and i didnt have another staff but i did have another RY with a battered dial so i robbed the balance and tweaked it around to make it work apart from that mostly just a good clean and relubrication. Keyless works are pretty rough by design and the crown is a bugger to get in and out with the dial on, the setting lever hits the dial before it releases it, so a little mod is needed to help that along. Major problem was the pins on the lever were quite worn which make the old tg have a snow storm fit. Its a similar read for most pin pallets, these were brass as was the escape wheel. But perseverance is me, i didn't change the pins but i did spend some time dressing and polishing the worn areas which improved the trace a lot with some straightish lines 😅 and a beat error of .5 . Not sure what the lift angle should be on these and i Wasn't in the mood to work it out and who believes timegraphers anyway, but at the default 52° it runs with 260ish full 210 after 24 hours dial down , the verticals rates were pretty much all over place. So lets just put it in it's superlight aluminium case and see what happens. Been wearing it now for 3 weeks and it's consistently losing around 1.5  minutes a week winding each morning i think pretty good for an old pin pallet watch. I just love this dial, thanks wifey heres my Valentine's gift for yer sweetie x
    • I have a PDF below that will help. The problem was the PDF wasn't designed for this purpose it was designed to tell you what size watch you  have. Then it doesn't take into account movements come conceivably in different thicknesses.   watch-ligne-size-chart.pdf
    • That would be something! Which brings me back to;  
    • you think you're going to sleep tonight you're not, you're going to ponder the question of what makes you think those of the right parts?  
    • Does anyone knows what size case a need for a dial diameter 20.60mm?
×
×
  • Create New...