Jump to content

Ebay seller trying to sound like he knows about clocks


JimmyD

Recommended Posts

Have a look at this Portico on eBay,

https://www.ebay.com.au/itm/Unusual-Portico-Clock-/153200303410?_trksid=p2047675.l2557&ssPageName=STRK%3AMEBIDX%3AIT&nma=true&si=lqgegTVV8zwAWHLgsxT9c6XOhhQ%253D&orig_cvip=true&nordt=true&rt=nc

Well the link did not work (new at this) so item number is 153200303410

The movement is very unusual and I think maybe Dutch, silk suspension however not sure as there is no way of adjusting it as I think the pendulum is not original but I may be wrong. The movement is like a reverse French and the arbour holes, well one in the centre the other about halfway on the dial.

The description, the guy is trying to sound as if he knows about clocks, i.e. movement is not going, not had time and later said, rings on a bell.  

Anyway it may get some discussion going.

Link to comment
Share on other sites

Ebay is full of people selling re-pro, stuff that does not appear to be what it is. Its like any auction in this case you have to know your clocks. There is a thread on here I think I started it about so called French carriage clocks and the Chinese fakes on ebay, I point out with the correct link at the time of auction. Longcase clocks that are a marriage, sometimes I run a little competition, to see if members can spot the mistakes.   

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Two pins or screwdrivers angled out slightly, pressing through from the barrel centre from the opposite side so they contact just clear of the hole in the lid? eg. Strap pin driver needles or similar.
    • That's a good idea - shrinking down the nut and wrench size from the old casebook trick!
    • I missed this earlier. The dial isn't going into the holder, it should sit proud of it. This is what I am currently using which I print for each different movement.    
    • I didn't think pulling to set position would work harden the spring, in that position it is stressed where the arm starts. By work hardening i meant rapid polishing at that point, a bit like polishing a pivot work hardens as it compresses the steel. I doubt polishing by hand would achieve much in that respect though. Its finished, arm polished up mostly at the join to the bridge's main body. I'm ok with it, the screw holes aren't great as i had to open them up by redrilling and positioning it was difficult, I'm not much use with a loupe, opening up with a file might be a better option for me or i could just use the correct drill size 😅. And the detent is way too deep, i had to guess that with the stem release out of position and sat on top, but i only took one measure and went for it, no slowly slowly catch your monkey 😅. First go I'm happy , well sort of, it works and thats a big thing for me, next one will have a bit more finesse.  Anyone thats interested, after filing, i used a 2000 grade home made diamond  micro file and then 20 micron film, the film is much better than wet and dry, more stable to use and doesn't shed cheap grade grit everywhere , then auto polish on a sponge pad.
    • I'm assuming that every time you set the watch you are work hardening the detent spring, maximum hardening is  where it meets the plate due to maximum deflection.   That's why it snaps there.  The Young's modulus may be the same but after it's reached its maximum yeid strength it breaks.  My mechanic engineering is very rusty, correct me if I'm wrong. 
×
×
  • Create New...