Jump to content

AS 1315 issue

rattandsonwatchmakers
 Share

Recommended Posts

HSL Distinguished Member

HSL

Posted
Posted

Just by judging from this one photo it´s hard to make any estimations
So just as a start and considering it stopped by the balance bridge I would suggest you take off the Winding mechanism and look at the backside of the swing weight. if it is getting caught in something like the screw holding the balance bridge you should see some scratches on the backside of it.
In general you should do something about the screwheads along the path the weight travels since they seem to have quite a loot metal shavings sticking up, just give them a quick polish so they are nice and flat othervice you might end up with small metal shavings inside the mechanism.

Link to comment
Share on other sites
rogart63 Distinguished Member

rogart63

Posted
Posted

It's probably the placement of the weight you haven't got right. Could be tricky to get right.  Haven't worked on a 1315 but have done the same on omega and tissot bumbers. The weight should rest halfway between the springs when not engaged in winding the movement up. 

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • ManSkirtBrew
      1972 Bulova President "E" Sea King 11ACACB movement

      By ManSkirtBrew · Posted

      Oh nice. I have a similar wedge style stump for my staking tool, so I'll give that a shot. Thanks!
    • joelcarvajal
      Gamblin Gamsol for cleaning?

      By joelcarvajal · Posted

      Thank you all for the replies!  Very informative! True enough, the Gamsol took some time to evaporate and does leave a residue. So not all naphtha are created equal!  Need to find alternatives then. i was able to try Hexane recommended by Alex and it seems great.  I wonder what the cons are?
    • GuyMontag
      1972 Bulova President "E" Sea King 11ACACB movement

      By GuyMontag · Posted

      Yeah, I saw that in the tech sheet but I don't see how it can be adequately cleaned with the friction pinion still in place. I've accidentally pulled the arbor right out of the wheel once when I used a presto tool to try and remove it. Mark shows how he does it with the Platax tool. Those are a little too pricey for me so I got one of these from Aliexpress and I just push down on the arbor with the end of my brass tweezers. That usually gets it most of the way out and then I just grab the wheel with one hand the and the friction pinion with the other and gently rotate them until it pops off. Probably not the best way but it's seemed to work for me so far.    
    • Zedster
      Movement inserted from crytal side

      By Zedster · Posted

      Thanks, Jon Sounds like a plan. Obviously I'll have the face on so do you think gripping with the holder will create any problems, but I will check in the morning to see how feasible it is but I assume it only needs to be lightly held. As for holding the movement instead of the holder won't be possible in this scenario as one hand will be puling on the stem while the other pushes the spring down. That was my initial concern is how the hell can I do this with only one pair of hands. All the other times I've had to remove the stem hasn't been a problem, apart from the force required to release the stem from the setting lever, but now I need to fit the face and hands its sent me into panic mode. If it had the screw type release things would be a lot simpler but that's life 😀   Another thing I will need to consider is once the dial and hands are fitted and the movement is sitting in the case I will need to turn it over to put the case screws in. I saw a vid on Wristwatch revival where he lightly fitted the crystal and bezel so he could turn it over, is this the only option or is there another method?      
    • nevenbekriev
      Main spring

      By nevenbekriev · Posted

      Hi Jon, do You think that relation spring torque - amplitude is linear? I would rather guess that the amplitude should be proportional to the square of the torque. I had once idea to check it, but still haven't.
×
×
  • Create New...