Jump to content

DeWalt Timex Ironman

surfluds

By surfluds
in Watch Repairs Help & Advice

 Share

Recommended Posts

surfluds New Member

surfluds

Posted
Posted

I have the above watch that has four small cross head screws holding the back of the case on.

My question is that these look rather worn so where are places to get these screws and what measurements would be needed?

The pic is not the actual watch but is the model.

TIA

Mike

DTIM.png

Link to comment
Share on other sites
qhartman Watch Enthusiast

qhartman

Posted
Posted

Unless you have another watch you can steal them from, it will be hard to say that they are "screw x".

You should be able to get those from a normal fastener supplier though. You just need to know the thread pitch, diameter, and length of the screws. You can measure the thread pitch with one of these: https://en.wikipedia.org/wiki/Thread_pitch_gauge

Note that metric and imperial systems measure screws differently of course, so if you're having trouble getting something that is exactly right, try using the other system. Googling around should get more details on getting the right measurements.
 

Link to comment
Share on other sites
clockboy Distinguished Member

clockboy

Posted
Posted
4 hours ago, surfluds said:

I have the above watch that has four small cross head screws holding the back of the case on.

My question is that these look rather worn so where are places to get these screws and what measurements would be needed?

The pic is not the actual watch but is the model.

TIA

Mike

DTIM.png

I replaced a battery in one of these last year. If I remember correctly there was nothing special with regard to the screws. I am sure once you have removed them and measured replacements will not difficult to find. 

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • RichardHarris123
      Chronograph Pusher Rod for EB8371-67 Snapped and Stuck in Button. Can't Unscrew.

      By RichardHarris123 · Posted

      I think it is friction fit, there are tools to remove them, cheaper versions are available. You could try adapting some pliers, see my crap drawing.  The pushers are available in various sizes, you could measure once the tube is removed. 
    • Malocchio
      Is this pallet fork over-locking?

      By Malocchio · Posted

      The entry jewel's not as bad but seems still too much lock. I do epilame the escape wheel and pallet jewels, then run dry for about 15 minutes, then put 9415 in exit jewel very little at a time and check with backlight how the oil's distributed.  Another question is about capped escape wheels. Should I somehow wear the epilame off the pivots before installing the wheel? I normally let the escape wheel run dry for that said 15 minutes when there's no cap jewel.
    • Malocchio
      Bezels - What am I doing wrong?

      By Malocchio · Posted

      Sometimes there's a certain place under the bezel where the case knife is supposed to be placed. In this borrowed pic there's a small crack at 3 o'clock. 
    • Waggy
      Bezels - What am I doing wrong?

      By Waggy · Posted

      Hi my fellow forum addicts, I'm writing this as I seem to have a hole in my knowledge (probably one of many!) I seem to have a horrible time removing bezels from watches. I am talking about the rotating type on sports/diving watches. I see many videos where the guy on screen barely inserts the case knife under the bezel and with no effort it pops off easily, then at the end it clicks back into place by hand with no effort. I am sure that part of this is due to skillful video editing, but I seem to wrestle with them, I have tried case knives and  even when using the tool below, I tighten it up in several positions and nothing happens. On a many occasions I have even warped the bezel in my attempts to remove it. Similarly, I have issues replacing bezels after cleaning etc. and often they have to be replaced using a press tool and inevitably are far too tight and will not rotate or loose to the point where they fall off or loose their click (perhaps due to micro warping when I tried to remove??). It is now to the point where I am actually avoiding watches with bezels as my success rate with them is terrible......please help!! In short I am asking: What am I doing wrong? What is the best method for removing bezels - how do you do it? What is the best method for replacing bezels - how do you do it? Any tips or tricks? Thanks  
    • ManSkirtBrew
      1972 Bulova President "E" Sea King 11ACACB movement

      By ManSkirtBrew · Posted

      Amplitude still seems low, but I'm going to let it run in a bit and revisit. Meanwhile, got the first layer of the calendar works together and made sure the date ring snaps to both in quickset and regular setting. The mechanism is pretty cool, so I took a video.  
×
×
  • Create New...