Jump to content

Beginner: How do I get these off?

p2n

By p2n
in All Things Clocks

 Share

Recommended Posts

p2n WRT Addict

p2n

Posted
Posted

(First post in months - moved mid Aug and it's still chaos here)

The new house was a fixer upper and the old guy was a a horder. We agreed to take it on with junk for a knock down price. Cleaning out the shed I found the skellington of a Napoleon Mantle clock. 20+ years in a damp shed and between the rot and the woodworm there wasn't much left and what was there disintegrated when I listed it. BUT there was a mechanism there - no face just the mech.

That was the best thing I found in there (in fact the only thing of note)

Never worked on a clock before but thought this would be a good intro. It appeared to have had a good oiling (read 3-in-1) at some point in the past so other than a few bits wasn't corroded. Pulled the fluff and wood debris out and gave it a blast in the cleaner.

Stripped it down except for two shafts - I think the ends are press on and simply need to be pulled off, but don't want to get it wrong and bugger it up. So how do I remove these two?

 

P1100086.thumb.JPG.2bb6360ee161d1a971862c5c46044185.JPG

P1100087.thumb.JPG.4d421287e6547638806c88e1d000f288.JPG

 

Link to comment
Share on other sites
oldhippy Distinguished Member

oldhippy

Posted
Posted

The gathering pallet will come off. Put two pairs of plier handles under the pallet and use them as levers, it will come off. The centre one you can do in the same way, but you need to mark in so it goes back in the exact same place otherwise the hands will be out when it strikes. If the centre hole is not worn, I suggest you leave it and the cleaning fluid will remove the dirt, you have a good gap so oiling can easily take place.      

Link to comment
Share on other sites
  • 2 weeks later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • rossjackson01
      Intro

      By rossjackson01 · Posted

      Welcome my friend. 
    • rossjackson01
      Help please.

      By rossjackson01 · Posted

      Been there. Worn that Tshirt.  'ping'. Hands and knees. Nothing. Nada. 20 minutes? Ha! I found it 7 month later. How? Well, after advice from a member, I invested in a £4 UV light torch.  Hands and knees looking for a 'ping' from a Sekonda, found them both within 30 seconds. UV makes the jewel shine. easy peasy. Could have taken longer. Just lucky on the location of the search. Hope this helps.
    • Rixy
      Broken lug

      By Rixy · Posted

      Thanks Dell. I thought about silver soldering. Have never done it but would like to give it a go. Do you think to put flux on the butted joint then run the solder in or to maybe brace it with a piece of scrap spring steel?
    • rossjackson01
      Without Our Forum

      By rossjackson01 · Posted

      Never and others. Yes, like you I do spend a fair amount of time reading the contents of this forum. I find it better that any other. Clear, lucid, no Prima Donas, and most of all an easy access without adverts. All thanks to Mark. God bless you mate. You give so much to many of us. What if? No Mark? Hypothetically. A forum. I did run a forum for a few years. Really enjoyed it, but became so engrossed that it did affect my health. I gave to to others to run. Not been back. It was very successful and rivalled a number of large paying sites. No adverts, no others but me. I did ask and listen to members comments and it worked well.    Costs Having a domain name, £10 annually.  Register the site with a forum company, free. Build the site using the forum company guide lines, free. It looked and ran almost the same a Mark's. All the same facilities. The cost was only £5 per month, but counted visits (views). If I recall, it was that price for 5,000 views. Each extra 5,000 views increased the price by £2 per month. Success was my own personal undoing. From £5 per month initially, it rose to £60 a month and looked like increasing. This was 10 years ago. I could not afford that, and asked it anyone would like to take over and someone did. I would assume that this is the price that Mark is funding for us all. His return is our continued comments on the internet about his course, and the fact that many of the big names on YouTube mention him as their Tutor. Those of us who have done, and are still using, his course, benefit. In comparison to other courses, I can't believe how cheap it is, and the value is exceptional. It is the structure that gives the value. Long may Mark reign. Ross  
    • TheQuietMan
      Help please.

      By TheQuietMan · Posted

      Hi all, total newbie to watchmaking and I've had a bit of a mishap. Just completing level 2 and was doing ok, but I was just on the last part of the reassembly of my ST3620 when the balance end stone shot across the room, just as I was trying to see if I had put the correct amount of oil between it and the balance end, aarrrgh! Been on my hands and knees combing the carpet for 20mins looking for it but to no avail. Does anybody know where I can get a replacement from and what to look for please?? Thanks.
×
×
  • Create New...