Jump to content

Beginner: How do I get these off?


p2n

Recommended Posts

(First post in months - moved mid Aug and it's still chaos here)

The new house was a fixer upper and the old guy was a a horder. We agreed to take it on with junk for a knock down price. Cleaning out the shed I found the skellington of a Napoleon Mantle clock. 20+ years in a damp shed and between the rot and the woodworm there wasn't much left and what was there disintegrated when I listed it. BUT there was a mechanism there - no face just the mech.

That was the best thing I found in there (in fact the only thing of note)

Never worked on a clock before but thought this would be a good intro. It appeared to have had a good oiling (read 3-in-1) at some point in the past so other than a few bits wasn't corroded. Pulled the fluff and wood debris out and gave it a blast in the cleaner.

Stripped it down except for two shafts - I think the ends are press on and simply need to be pulled off, but don't want to get it wrong and bugger it up. So how do I remove these two?

 

P1100086.thumb.JPG.2bb6360ee161d1a971862c5c46044185.JPG

P1100087.thumb.JPG.4d421287e6547638806c88e1d000f288.JPG

 

Link to comment
Share on other sites

The gathering pallet will come off. Put two pairs of plier handles under the pallet and use them as levers, it will come off. The centre one you can do in the same way, but you need to mark in so it goes back in the exact same place otherwise the hands will be out when it strikes. If the centre hole is not worn, I suggest you leave it and the cleaning fluid will remove the dirt, you have a good gap so oiling can easily take place.      

Link to comment
Share on other sites

  • 2 weeks later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • That would be something! Which brings me back to;  
    • you think you're going to sleep tonight you're not, you're going to ponder the question of what makes you think those of the right parts?  
    • Does anyone knows what size case a need for a dial diameter 20.60mm?
    • Sounds like the story with my Rolex. Poor (expensive) job done by an official Rolex dealer with an "in-house" watchmaker, hence I learned watchrepair and did the servicing myself. Same story as I learned with the Omega 861, again poor job by an "in-house" watchmaker by an official Omega dealer. Once your watch goes through that back-door, you have no idea what is going to happening to it 🫣   Quite nice that they sent back the parts which had been replaced !
    • yes that's definitely not right at all. I have a picture one of my friends has a Omega coaxial there was having issues to lose asking me where he should send it. As that's a specialty watch I suggested the service center. When he got it back he sent me a picture so the replace the dial as you can see the hands the mainspring barrel and I think the price was really quite decent considering all the stuff they can replace. So I do know they do change the barrels but the other person I worked at the service center when I would ask questions and unfortunately I can't remember all the answers. I think a lot of the changing a parts is at the discretion of the watchmaker. Plus I don't know enough about the chronographs and whether that would be considered a vintage watch? I take some of the vintage watches may have been sent directly to Switzerland or another service center. Obviously with a watch like the one down below they probably have a infinite supply of parts is its relatively modern vintage stuff becomes more interesting even the watch companies don't have necessarily infinite supply of parts. But no matter what the watch shouldn't disintegrated six months that's definitely an issue.        
×
×
  • Create New...