Jump to content

What type crystal?


Lc130

Recommended Posts

Hi All

I'm a beginner trying to determine what type of crystal to order.  The supply house describes them as glued in, compression fit or tension ring.

They would be for a Waltham and Sears Tradition.  Both from late 60's early 70's.  

I was able to easily pop both crystals out.  The Sears crystal has a smooth edge and the Waltham has a lip. Neither had a gasket or ring.

Almost impossible to get clear pictures but these are looking at the inner wall of the case, top up (Sears first)

Any ideas of the type of crystals?

Thank you

Charlie

 

 

 

 

 

 

 

 

sears.jpg

waltham.jpg

Link to comment
Share on other sites

I would say if they do not have sweep seconds hands Low dome will fit. High dome if they have sweep seconds. Measure from 12 to 6 or 9 to 3. What tool do you have for fitting crystals?

Just a thought did the old ones have a ring inside the crystal?

Link to comment
Share on other sites

Follow up...

The Waltham face opening is 30mm.  The old crystal measured 30.2 including the small lip.  The other is 30mm with no lip.  

I honestly can't determine what crystal to select from this supplier.  https://www.jewelerssupplies.com/CrystalsPlastic.html

Any help is appreciated.

 

 

Edited by Lc130
Link to comment
Share on other sites

The bezel looks deep enough. That tool will squeeze the crystal when it picks it up, so a slightly bigger size will fit in.  

 

Go here and look for HD BCL 30.2 then click on Alternatives a small window will open that is what you need buy 2 one for each.  

https://www.cousinsuk.com/product/domed-high-bcl-bhd

I do not understand all the info from your link. You could phone and tell them what you want. 

Link to comment
Share on other sites



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Haha. You're just in a wicked mood today John 😅
    • Heres my watch of today, a Smith 13'" RY . My missus bought me this for this Valentines day a bargain 14.99 with a reduction, the seller has occasional 20% off offers now and then so it was about 15ish with delivery. I love Smiths and i love bulleye dials, this is my first one. The watch arrived non working as stated and i knew what was inside and what would be against me, but i enjoy a challenge, we dont expect a lot if anything from pin pallet movements. A balance pivot was broken and i didnt have another staff but i did have another RY with a battered dial so i robbed the balance and tweaked it around to make it work apart from that mostly just a good clean and relubrication. Keyless works are pretty rough by design and the crown is a bugger to get in and out with the dial on, the setting lever hits the dial before it releases it, so a little mod is needed to help that along. Major problem was the pins on the lever were quite worn which make the old tg have a snow storm fit. Its a similar read for most pin pallets, these were brass as was the escape wheel. But perseverance is me, i didn't change the pins but i did spend some time dressing and polishing the worn areas which improved the trace a lot with some straightish lines 😅 and a beat error of .5 . Not sure what the lift angle should be on these and i Wasn't in the mood to work it out and who believes timegraphers anyway, but at the default 52° it runs with 260ish full 210 after 24 hours dial down , the verticals rates were pretty much all over place. So lets just put it in it's superlight aluminium case and see what happens. Been wearing it now for 3 weeks and it's consistently losing around 1.5  minutes a week winding each morning i think pretty good for an old pin pallet watch. I just love this dial, thanks wifey heres my Valentine's gift for yer sweetie x
    • I have a PDF below that will help. The problem was the PDF wasn't designed for this purpose it was designed to tell you what size watch you  have. Then it doesn't take into account movements come conceivably in different thicknesses.   watch-ligne-size-chart.pdf
    • That would be something! Which brings me back to;  
    • you think you're going to sleep tonight you're not, you're going to ponder the question of what makes you think those of the right parts?  
×
×
  • Create New...