Jump to content

Raymond Weil 9514.5

Chadders

By Chadders
in Watch Repairs Help & Advice

 Share

Recommended Posts

Chadders Member

Chadders

Posted
Posted

My partner obtained  a quartz Raymond Weil 9514.50for me to  repair, granted its a quartz ugh!!! but it loses 20 mins  a night, but maintains time during the day when worn, have changed the battery but this has not changed the situation, any ideas? can you obtain a new movement reasonably cheaply?? Cousinsuk do not even list the manufacturer.

 

Comments welcome

Link to comment
Share on other sites
nad WRT Addict

nad

Posted
Posted

Before replacing the movement, it might be worth checking if the hands are making contact with each other at some stage in their rotation.

Repaired a Tissot quartz a while back which was losing time as a result of a slight drag as the second hand passed over the minute hand. When worn it lost a little time but when left on the bedside table for a while it sometimes stopped.



Sent from my moto g(6) play using Tapatalk

Link to comment
Share on other sites
AndyHull Distinguished Member

AndyHull

Posted
Posted (edited)

If that line of fault finding leads nowhere, then it could be an electrical issue. I'm no expert on quartz movements specifically, but I do have a background in electronics, so I can offer a few suggestions.

I would check the battery contacts are clean, and that there is no obvious sign of corrosion anywhere, then inspect the module very carefully for hairline cracks and damaged solder joints.

It doesn't take much with the very low power levels involved for things to get out of whack. A loose connection on one end of the crystal, or moisture damage or a crack to one of the resistors or capacitors, and things get strange when they cool down or warm up. 

If you have access to an oscilloscope, things get a lot easier, but assuming you don't, then start with those suggestions first and we will see if we can get to the source of the issue.

If you post some closeup pictures, then I might be able to offer some other thoughts.

Edited by AndyHull
Link to comment
Share on other sites
Nucejoe Distinguished Member

Nucejoe

Posted
Posted

I havn,t seen a pic of the movement.

If its got day or even date, the day jump works can very well be the fault, advance time by 12 hrs = swith day& night around, it then should loose 20 min day time and go accurate at nights.

  • Like 1
Link to comment
Share on other sites
AndyHull Distinguished Member

AndyHull

Posted
Posted
1 minute ago, Nucejoe said:

I havn,t seen a pic of the movement.

If its got day or even date, the day jump works can very well be the fault, advance time by 12 hrs = swith day& night around, it then should loose 20 min day time and go accurate at nights.

Good suggestion. I would try that first before messing about with my suggestions, also some good pictures would help

Link to comment
Share on other sites
Chadders Member

Chadders

Posted
  • Author
Posted
37 minutes ago, nad said:

Before replacing the movement, it might be worth checking if the hands are making contact with each other at some stage in their rotation.

Repaired a Tissot quartz a while back which was losing time as a result of a slight drag as the second hand passed over the minute hand. When worn it lost a little time but when left on the bedside table for a while it sometimes stopped.



Sent from my moto g(6) play using Tapatalk
 

Thanks, it has no second hand and I followed your advice, sadly I CAN see daylight between the minute and hour hand when placed at 12 noon, so sadly this easy fix seems unlikely. The movement is an  556.031 im told ETA do an equivalent. 

 

2 minutes ago, AndyHull said:

If that line of fault finding leads nowhere, then it could be an electrical issue. I'm no expert on quartz movements specifically, but I do have a background in electronics, so I can offer a few suggestions.

I would check the battery contacts are clean, and that there is no obvious sign of corrosion anywhere, then inspect the module very carefully for hairline cracks and damaged solder joints.

It doesn't take much with the very low power levels involved for things to get out of whack. A loose connection on one end of the crystal, or moisture damage or a crack to one of the resistors or capacitors, and things get strange when they cool down or warm up. 

If you have access to an oscilloscope, things get a lot easier, but assuming you don't, then start with those suggestions first and we will see if we can get to the source of the issue.

 

Link to comment
Share on other sites
Nucejoe Distinguished Member

Nucejoe

Posted
Posted
2 minutes ago, AndyHull said:

Good suggestion. I would try that first before messing about with my suggestions, also some good pictures would help

Hi andy I guess I get medals only if that fixes the movement.  Remember?  :geek: 

Regards joe

Link to comment
Share on other sites
AndyHull Distinguished Member

AndyHull

Posted
Posted
Just now, Nucejoe said:

Hi andy I guess I get medals only if that fixes the movement.  Remember?  :geek: 

Regards joe

 

No fix, no medal, thems the rules :D

I suspect the movement should look something like this.
Quartz.png.0529e58bf808746e316e3ab730ca2255.png

It seems it has been superseded by the ETA 956.031/2 Movement (double check that before you purchase though). 

My suggestions to check for poor solder, corrosion, cracked components etc. still stand. If you are feeling brave (or foolish) you could try cleaning the mechanicals too. Whats the worst that can happen, you have to replace the movement. 

Link to comment
Share on other sites
Chadders Member

Chadders

Posted
  • Author
Posted
9 minutes ago, AndyHull said:

No fix, no medal, thems the rules :D

I suspect the movement should look something like this.
Quartz.png.0529e58bf808746e316e3ab730ca2255.png

It seems it has been superseded by the ETA 956.031/2 Movement (double check that before you purchase though). 

My suggestions to check for poor solder, corrosion, cracked components etc. still stand. If you are feeling brave (or foolish) you could try cleaning the mechanicals too. Whats the worst that can happen, you have to replace the movement. 

Many thanks, now the fog is clearing, could not find the original movement ref on any site, may just replace the movement. 

 

David

Link to comment
Share on other sites
TexasDon WRT Addict

TexasDon

Posted
Posted (edited)
On 1/7/2019 at 6:36 AM, AndyHull said:

It ain't the cheapest movement I've ever encountered, considering it is just a simple two hander :( 

http://www.ofrei.com/page548.html
http://www.watchpartssupply.com/eta-9560312-movement-p-297.html
 

It's Swiss. What else can you expect? I did fine an original 556.031, new,  listed on the US version of fleabay for $400. Ouch! The seller must be assuming that someone wishes to restore a valuable heirloom.

Edited by TexasDon
additional info
Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • rjenkinsgb
      My first Gruens. Precision 510 and N510R movements.

      By rjenkinsgb · Posted

      Snap! I recently finished my Gruen 510 movement - though the case for mine is in a rather sad state; I'm going to try re-plating it (in nickel, it's not a gold one).   Re. the screws, I got a few of the one gram mixed batches from ebay. I've only needed a couple of screws for things so far, both rare, minuscule types - but both in the mix, after enough time sorting through them! The ones such as normal bridge screws are quite common in those lots.  
    • rjenkinsgb
      Any tips to correct a sloppy error?

      By rjenkinsgb · Posted

      Two pins or screwdrivers angled out slightly, pressing through from the barrel centre from the opposite side so they contact just clear of the hole in the lid? eg. Strap pin driver needles or similar.
    • Geotex
      Any tips to correct a sloppy error?

      By Geotex · Posted

      That's a good idea - shrinking down the nut and wrench size from the old casebook trick!
    • GuyMontag
      Movement holder made with 3D printer

      By GuyMontag · Posted

      I missed this earlier. The dial isn't going into the holder, it should sit proud of it. This is what I am currently using which I print for each different movement.    
    • Neverenoughwatches
      Setting lever spring

      By Neverenoughwatches · Posted

      I didn't think pulling to set position would work harden the spring, in that position it is stressed where the arm starts. By work hardening i meant rapid polishing at that point, a bit like polishing a pivot work hardens as it compresses the steel. I doubt polishing by hand would achieve much in that respect though. Its finished, arm polished up mostly at the join to the bridge's main body. I'm ok with it, the screw holes aren't great as i had to open them up by redrilling and positioning it was difficult, I'm not much use with a loupe, opening up with a file might be a better option for me or i could just use the correct drill size 😅. And the detent is way too deep, i had to guess that with the stem release out of position and sat on top, but i only took one measure and went for it, no slowly slowly catch your monkey 😅. First go I'm happy , well sort of, it works and thats a big thing for me, next one will have a bit more finesse.  Anyone thats interested, after filing, i used a 2000 grade home made diamond  micro file and then 20 micron film, the film is much better than wet and dry, more stable to use and doesn't shed cheap grade grit everywhere , then auto polish on a sponge pad.
×
×
  • Create New...