Jump to content

Raymond Weil 9514.5

Chadders

By Chadders
in Watch Repairs Help & Advice

 Share

Recommended Posts

Chadders Member

Chadders

Posted
Posted

My partner obtained  a quartz Raymond Weil 9514.50for me to  repair, granted its a quartz ugh!!! but it loses 20 mins  a night, but maintains time during the day when worn, have changed the battery but this has not changed the situation, any ideas? can you obtain a new movement reasonably cheaply?? Cousinsuk do not even list the manufacturer.

 

Comments welcome

Link to comment
Share on other sites
nad WRT Addict

nad

Posted
Posted

Before replacing the movement, it might be worth checking if the hands are making contact with each other at some stage in their rotation.

Repaired a Tissot quartz a while back which was losing time as a result of a slight drag as the second hand passed over the minute hand. When worn it lost a little time but when left on the bedside table for a while it sometimes stopped.



Sent from my moto g(6) play using Tapatalk

Link to comment
Share on other sites
AndyHull Distinguished Member

AndyHull

Posted
Posted (edited)

If that line of fault finding leads nowhere, then it could be an electrical issue. I'm no expert on quartz movements specifically, but I do have a background in electronics, so I can offer a few suggestions.

I would check the battery contacts are clean, and that there is no obvious sign of corrosion anywhere, then inspect the module very carefully for hairline cracks and damaged solder joints.

It doesn't take much with the very low power levels involved for things to get out of whack. A loose connection on one end of the crystal, or moisture damage or a crack to one of the resistors or capacitors, and things get strange when they cool down or warm up. 

If you have access to an oscilloscope, things get a lot easier, but assuming you don't, then start with those suggestions first and we will see if we can get to the source of the issue.

If you post some closeup pictures, then I might be able to offer some other thoughts.

Edited by AndyHull
Link to comment
Share on other sites
Nucejoe Distinguished Member

Nucejoe

Posted
Posted

I havn,t seen a pic of the movement.

If its got day or even date, the day jump works can very well be the fault, advance time by 12 hrs = swith day& night around, it then should loose 20 min day time and go accurate at nights.

  • Like 1
Link to comment
Share on other sites
AndyHull Distinguished Member

AndyHull

Posted
Posted
1 minute ago, Nucejoe said:

I havn,t seen a pic of the movement.

If its got day or even date, the day jump works can very well be the fault, advance time by 12 hrs = swith day& night around, it then should loose 20 min day time and go accurate at nights.

Good suggestion. I would try that first before messing about with my suggestions, also some good pictures would help

Link to comment
Share on other sites
Chadders Member

Chadders

Posted
  • Author
Posted
37 minutes ago, nad said:

Before replacing the movement, it might be worth checking if the hands are making contact with each other at some stage in their rotation.

Repaired a Tissot quartz a while back which was losing time as a result of a slight drag as the second hand passed over the minute hand. When worn it lost a little time but when left on the bedside table for a while it sometimes stopped.



Sent from my moto g(6) play using Tapatalk
 

Thanks, it has no second hand and I followed your advice, sadly I CAN see daylight between the minute and hour hand when placed at 12 noon, so sadly this easy fix seems unlikely. The movement is an  556.031 im told ETA do an equivalent. 

 

2 minutes ago, AndyHull said:

If that line of fault finding leads nowhere, then it could be an electrical issue. I'm no expert on quartz movements specifically, but I do have a background in electronics, so I can offer a few suggestions.

I would check the battery contacts are clean, and that there is no obvious sign of corrosion anywhere, then inspect the module very carefully for hairline cracks and damaged solder joints.

It doesn't take much with the very low power levels involved for things to get out of whack. A loose connection on one end of the crystal, or moisture damage or a crack to one of the resistors or capacitors, and things get strange when they cool down or warm up. 

If you have access to an oscilloscope, things get a lot easier, but assuming you don't, then start with those suggestions first and we will see if we can get to the source of the issue.

 

Link to comment
Share on other sites
Nucejoe Distinguished Member

Nucejoe

Posted
Posted
2 minutes ago, AndyHull said:

Good suggestion. I would try that first before messing about with my suggestions, also some good pictures would help

Hi andy I guess I get medals only if that fixes the movement.  Remember?  :geek: 

Regards joe

Link to comment
Share on other sites
AndyHull Distinguished Member

AndyHull

Posted
Posted
Just now, Nucejoe said:

Hi andy I guess I get medals only if that fixes the movement.  Remember?  :geek: 

Regards joe

 

No fix, no medal, thems the rules :D

I suspect the movement should look something like this.
Quartz.png.0529e58bf808746e316e3ab730ca2255.png

It seems it has been superseded by the ETA 956.031/2 Movement (double check that before you purchase though). 

My suggestions to check for poor solder, corrosion, cracked components etc. still stand. If you are feeling brave (or foolish) you could try cleaning the mechanicals too. Whats the worst that can happen, you have to replace the movement. 

Link to comment
Share on other sites
Chadders Member

Chadders

Posted
  • Author
Posted
9 minutes ago, AndyHull said:

No fix, no medal, thems the rules :D

I suspect the movement should look something like this.
Quartz.png.0529e58bf808746e316e3ab730ca2255.png

It seems it has been superseded by the ETA 956.031/2 Movement (double check that before you purchase though). 

My suggestions to check for poor solder, corrosion, cracked components etc. still stand. If you are feeling brave (or foolish) you could try cleaning the mechanicals too. Whats the worst that can happen, you have to replace the movement. 

Many thanks, now the fog is clearing, could not find the original movement ref on any site, may just replace the movement. 

 

David

Link to comment
Share on other sites
TexasDon WRT Addict

TexasDon

Posted
Posted (edited)
On 1/7/2019 at 6:36 AM, AndyHull said:

It ain't the cheapest movement I've ever encountered, considering it is just a simple two hander :( 

http://www.ofrei.com/page548.html
http://www.watchpartssupply.com/eta-9560312-movement-p-297.html
 

It's Swiss. What else can you expect? I did fine an original 556.031, new,  listed on the US version of fleabay for $400. Ouch! The seller must be assuming that someone wishes to restore a valuable heirloom.

Edited by TexasDon
additional info
Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • DDean
      Incabloc Lyre Spring & Low Earth Orbit

      By DDean · Posted

      Just a note for those who come searching for information on this topic in the future.  I did eventually find the Mark's video on how to replace these springs, as someone observed, he does in fact make the replacement look easy.  (It actually is relatively easy once you have the knack of it.) If you're enrolled in one of Mark's online courses, the demonstration of how to replace this spring is in the Bonus Videos section of his course site, and is called "C2B1 – Sea-Gull Style Shock Springs".
    • RichardHarris123
      Setting lever spring

      By RichardHarris123 · Posted

      If the metal was twice as thick, it wouldn't snap so easily.  The thickness is governed by the space available so you can't use thicker metal.  If you glued two pieces together, the likelihood of snapping would be reduced.  That's my theory anyway, could be wrong. 
    • JohnR725
      Pocket watch escape wh

      By JohnR725 · Posted

      there are various approaches to learning watch repair. A lot of people want to jump right in and every single watches something to be repaired restored. But other times like this it's disposable it's here for you to learn and when you're through learning you throw it away. yes you definitely should try this you have a learning movement you need to learn and the best way to learn is by doing something.
    • nevenbekriev
      Pocket watch escape wh

      By nevenbekriev · Posted

      Sorry, the friction will be so great that the wheel will barely turn, if the movement will start at all, the amplitude will be verry lo.
    • Bonefixer
      Pocket watch escape wh

      By Bonefixer · Posted

      If I can’t re-pivot the wheel, the logical thing to do is to descend the pivot hole.  Plan is to either stick a suitably sized hole jewel (from a barrel bridge or something) or fashion a blob of epoxy on the underside of the escape wheel cock so the wheel sits on its one pivot on the base plate and the staff with the broken off pivot (which I’ll polish as best as I can) becomes the upper pivot. As long as it doesn’t foul the 4th wheel it should work? I know it’s a bodge job, and if this were a rare movement, or belonged to someone else I would not do this. I’m just interested to see if I can get the thing to run. 
×
×
  • Create New...