Jump to content

Large variations in rate

Lc130

By Lc130
in Watch Repairs Help & Advice

 Share

Recommended Posts

Lc130 WRT Addict

Lc130

Posted
Posted

Hi All

I'm learning on an AS 1700.  I disassembled, cleaned, oiled to best of my beginner ability and reassembled. I didn't change or attempt to clean the mainspring. 

On the timegrapher the rate varies tremendously from +900 to +132.  Over the course of several minutes it varied +130 to +200.

The amplitude varies from 175 to 235.  The beat error varies from 0.7 to 1.8. 

Would this be attributed to the mainspring or something else?

Thank you for any comments,

Charlie

 

 

 

Link to comment
Share on other sites
qhartman Watch Enthusiast

qhartman

Posted
Posted

I'm also a rookie, but I would expect large variation in amplitude to be a problem with the balance wheel, or with something along the gear train causing inconsistent power delivery, not a problem with the mainspring itself. Anxious to hear what more experienced folks have to say too!

Link to comment
Share on other sites
yankeedog Distinguished Member

yankeedog

Posted
Posted (edited)

rate of fluctuation ? how many seconds? very short intervals look at your escape wheel , longer intervals fourth wheel, maybe  something out of true or round or wobbling

Edited by yankeedog
content
Link to comment
Share on other sites
oldhippy Distinguished Member

oldhippy

Posted
Posted

You should have cleaned the m/spring. Without looking at it you do not know what the condition of it. What oil have you used on the train and the escapement, you might have used too much. These are just two of many things why the movement is keeping erratic time.

Link to comment
Share on other sites
Nucejoe Distinguished Member

Nucejoe

Posted
Posted

AS 1700 features detached manual wind with corresponding gear underneath barrel. Barrel and mainspring are part of power train, should be cleaned and lubed as OH advised

Periodic rate fluctuation is sinusoidal, which corresponds with period of each wheel and barrel to whcih yankee refered. Non-periodic fluctuations are to be attributed to loose objects affecting the power transfer in the train ie;  broken pieces, loose screw, dirt.  As well as grooves in barrel lid or bottom plate.

" over the course of several minutes".  is talking to us, several minutes is beyond the period of escape and minute wheel  so the answer to your question is YES it can be attributed to mainspring and barrel mostly on account of dirt or grooves.

Before removing the barrel, use the manual wind readily at your disposal to bring the MS  to full wind, observe how long it runs ( actual power reserve) gives an idea of MS strength. It may need a new mainspring too.

 

Link to comment
Share on other sites
nickelsilver Distinguished Member

nickelsilver

Posted
Posted

As above, this could be any number of things. You have to go through systematically: check the train freedom, check that the pallet fork is free, check that the balance is free (minus pallet fork). In all likelihood it should run fairly well, even with an unserviced barrel,  definitely better than what you have. Like rodabod said, with such a huge gain there is almost certainly an issue with the hairspring- but don't mess around there until you've done all the basic checks. And do, do peg out the jewel holes- particularly the hole jewels for the fork.

  • Like 1
Link to comment
Share on other sites
oldhippy Distinguished Member

oldhippy

Posted
Posted

It always good practise to demagnetise the watch and any tools you are going to use first. Seiko barrels are made in such a way that they should not be opened, The practise years ago was to replace the whole unit every (I think 5 years) because many complete units have become obsolete you have no alternative but to open the barrel and replace the spring if needed.     

Link to comment
Share on other sites
rodabod Distinguished Member

rodabod

Posted
Posted

I should have also added to check that the hairspring and movement are not magnetised.

The only other time I can remember experiencing an extreme gain in rate other than "knocking the bankings" (due to excess amplitude) was when I had a safety roller which wasn't playing ball with the pallet that caused a similar effect by causing the balance wheel to immediately bounce back every time it swung in one direction.

Link to comment
Share on other sites
Lc130 WRT Addict

Lc130

Posted
  • Author
Posted

Thank you all for the help!  I disassembled and reinspected the wheels which appear to be true.  I did not peg out the jewel holes and will do that.  

I used Mobius 8000 oil which I was told would be sufficient for learning.  

Below are pics of the mainspring.  Should it be replaced or will a cleaning do?  Does this spring need a breaking grease in the barrel?

Thank you

Charlie

 

 

IMG_3299.JPG

IMG_3305.JPG

IMG_3306.JPG

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Zedster
      Movement inserted from crytal side

      By Zedster · Posted

      Hi, guys I have a bit of a predicament and hopefully, somebody can advise. I'm working on a Roamer MST 521 where the movement is extracted from the crystal side. I'm now at the final hurdle where I need to replace the movement back into its case but I'm not sure of the correct procedure. I still need to fit the hands but that's where the problem lies. If I insert the winding stem to test the hands for correct alignment I will need to turn the movement over to release the stem again it's the spring-loaded type and needs a small bit of force to push down but with the hands fitted, I don't think I can do this on a cushion without causing some damage to the hands and that's the last thing I want to do, this watch has already been a love-hate relationship and I'm so close to boxing this one off which I'm counting as my first major project.  The other option is to case the movement then fit the hands and hope everything is okay. I've already broken the original winding stem but managed to find a replacement, the last one in stock, so I'm a bit reluctant to keep removing it. Any suggestions would be appreciated. 
    • Jon
      Main spring

      By Jon · Posted

      I would go for the dearer spring. You won't need to remove the spring from the carrier ring and then use a mainspring winder to get it into the barrel, for a start. Also that spring is closer to the needed dimensions, especially the length. The length plays a part in the mainsprings strength. If you double the length you will half the force (strength) of the spring and vice-versa. A spring with 20 mm less length would be about 7% shorter, so technically would be 7% more strength, but I find halving this number is closer to real-world findings, so the spring would be about 3 to 4% more strength/force. On a mainspring that ideally kicks out 300 degrees of amplitude, a 3% increase in amplitude would be 309 degrees. Increasing or decreasing the length of the mainspring will affect the power reserve to a greater or lesser degree. It depends how much shorter or longer it is.
    • Malocchio
      What tools does ebay have to offer this week.

      By Malocchio · Posted

      I recently bought this but not on ebay. I figured if I want something Japanese I better check Japanese auction sites since these don't seem to pop up on ebay. I paid 83 € plus shipping & taxes. I think it was pretty reasonable for a complete set in good condition.
    • GuyMontag
      1972 Bulova President "E" Sea King 11ACACB movement

      By GuyMontag · Posted

      Did you take the friction pinion off the large driving wheel and grease it? Although, now that I think about it, that shouldn't have any effect on the free running of the train if the friction pinion isn't interacting withe minute wheel/setting wheel...
    • DDean
      Incabloc Lyre Spring & Low Earth Orbit

      By DDean · Posted

      I did in fact use Rodico to get the spring into general position and "hold" it there while I used a fine oiler to make subtle positional adjustments.
×
×
  • Create New...