Jump to content

Is there a tool?

TexasDon

By TexasDon
in Tools & Equipment

 Share

Recommended Posts

TexasDon WRT Addict

TexasDon

Posted
Posted

For removing the oscillating weight from a Seiko 7S26 etc. watch movement. I can always use a screwdriver but the slot is actually quite long and it has the bearing race in the middle. Something with a split point I would assume. If one exists, can you point me in the correct direction? My primary goal is to not bugger up the screw slot. You have no idea what I'm really capable of in that area!

Link to comment
Share on other sites
rogart63 Distinguished Member

rogart63

Posted
Posted
1 hour ago, vinn3 said:

  does the counter  weight have a pressed in roller bearing?     on the few i have removed,   the bearing is in an assembly that  is srewed on.  vin

Think so. On 6309 and some other Seiko it's impossible to remove without breaking the oscillating weight or the bearing. 

Link to comment
Share on other sites
TexasDon WRT Addict

TexasDon

Posted
  • Author
Posted (edited)

The bearing is non removable. A new counterweight has to be used if the bearings are damaged for any reason. Part of this, in fact a large part of this, is me being totally **BLEEP** about not abiding a buggered up screw head. It sends me into a low earth orbit and just shrieks of malpractice IMHO. I learned gunsmithing, up to a point, many years ago and my mentor was a stickler for never sending a piece back out with a damaged screw head in any area that he had worked on. To me, the only worse offense is to find a hair wrapped around a pivot when opening a used watch. 

If such a tool exists, I can't find it and I've really looked. I did find a Wiha 4mm x 70mm total length miniature screwdriver. I believe that I can use this to make a proper tool. I will dress the tip to fit into the slot exactly, then use a round file to remove enough metal from the center of the blade to provide proper relief for the bearing race. Other than that, I'm fresh out of ideas.

Edited by TexasDon
spelling, grammar
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • rossjackson01
      Intro

      By rossjackson01 · Posted

      Welcome my friend. 
    • rossjackson01
      Help please.

      By rossjackson01 · Posted

      Been there. Worn that Tshirt.  'ping'. Hands and knees. Nothing. Nada. 20 minutes? Ha! I found it 7 month later. How? Well, after advice from a member, I invested in a £4 UV light torch.  Hands and knees looking for a 'ping' from a Sekonda, found them both within 30 seconds. UV makes the jewel shine. easy peasy. Could have taken longer. Just lucky on the location of the search. Hope this helps.
    • Rixy
      Broken lug

      By Rixy · Posted

      Thanks Dell. I thought about silver soldering. Have never done it but would like to give it a go. Do you think to put flux on the butted joint then run the solder in or to maybe brace it with a piece of scrap spring steel?
    • rossjackson01
      Without Our Forum

      By rossjackson01 · Posted

      Never and others. Yes, like you I do spend a fair amount of time reading the contents of this forum. I find it better that any other. Clear, lucid, no Prima Donas, and most of all an easy access without adverts. All thanks to Mark. God bless you mate. You give so much to many of us. What if? No Mark? Hypothetically. A forum. I did run a forum for a few years. Really enjoyed it, but became so engrossed that it did affect my health. I gave to to others to run. Not been back. It was very successful and rivalled a number of large paying sites. No adverts, no others but me. I did ask and listen to members comments and it worked well.    Costs Having a domain name, £10 annually.  Register the site with a forum company, free. Build the site using the forum company guide lines, free. It looked and ran almost the same a Mark's. All the same facilities. The cost was only £5 per month, but counted visits (views). If I recall, it was that price for 5,000 views. Each extra 5,000 views increased the price by £2 per month. Success was my own personal undoing. From £5 per month initially, it rose to £60 a month and looked like increasing. This was 10 years ago. I could not afford that, and asked it anyone would like to take over and someone did. I would assume that this is the price that Mark is funding for us all. His return is our continued comments on the internet about his course, and the fact that many of the big names on YouTube mention him as their Tutor. Those of us who have done, and are still using, his course, benefit. In comparison to other courses, I can't believe how cheap it is, and the value is exceptional. It is the structure that gives the value. Long may Mark reign. Ross  
    • TheQuietMan
      Help please.

      By TheQuietMan · Posted

      Hi all, total newbie to watchmaking and I've had a bit of a mishap. Just completing level 2 and was doing ok, but I was just on the last part of the reassembly of my ST3620 when the balance end stone shot across the room, just as I was trying to see if I had put the correct amount of oil between it and the balance end, aarrrgh! Been on my hands and knees combing the carpet for 20mins looking for it but to no avail. Does anybody know where I can get a replacement from and what to look for please?? Thanks.
×
×
  • Create New...