Jump to content

Making a display back window in a plain back


Vacherin

Recommended Posts

I have a few generic cases that I could chuck up in the lathe and machine a recess in the back with tapered sides. The idea is then to heat the back, put the glass in the freezer, and shrink fit it. Can I just use mineral glass (ie, from a window!). I have never worked with glass other than cutting panes for house windows (not easy!). I guess I can grind the glass while super glued on a mandrel, using a dremel while the glass rotates?

What sort of taper angle should I aim for? Any idea what thickness of glass I should use?

I have access to a surface grinder with a magnetic table. I was thinking that if the glass was thick when I fitted it I could take off a mm, then hand polish using silicon carbide powder on a glass block.

Is this all impractical?

I did consider making a screw back from scratch, but was not sure how to cut the thread, and I still would need to know how to fit the glass.

Link to comment
Share on other sites

Round mineral glasses are available in all sizes for little money.
Thickness starts at 0.8mm afaik. 
They are glued in or pressed using a gasket.
Window must have 90 deg edges. 
A too thin back can be an issue, test before cutting!

Frank

  • Like 2
Link to comment
Share on other sites

I think if you try to shrink fit it it will break, if not upon installation then down the road from being under tension. As above, a gasket or glue are the usual ways to install. Be wary when cutting away the inside of your back as you get toward the tapered sides you will lower the level of the glass, possibly crashing into the movement. On one odd customer request I once added a pressed in stainless ring to the opened back which blended in and added the necessary height.

  • Like 2
Link to comment
Share on other sites

Another option would be to cut it to fit a low dome acrylic crystal.you could install it with a crystal lift.nice tight fit.you might even be able to install one in the back of the case with no machining of anything..I have never tried it.but it might just work

Edited by yankeedog
Spelling
Link to comment
Share on other sites

Nickelsilver that is an amazing picture thanks! I have not thought about the crystal hitting the movement. That looks like an attractive way of getting round that problem. Yankeedog I did see an Omega on here that someone had simply fitted a crystal to the back of.

Link to comment
Share on other sites

On ‎12‎/‎17‎/‎2018 at 9:02 PM, nickelsilver said:

Here's the one with the added ring. Customer had a case he wanted to use for sentimental reasons and fit a vintage monopusher chrono in. Not the best pic but only one I have. Movement was old enough to be pin setting you can see the added pin next to crown. fe146f414188838a99088d445e65d485.jpg&key=9060778ac461341f882b6a1b170bbe0fdebd1657667f16670a13dcbf7e7ac507

 

 

Sorry, did you make that case back?  That looks incredible!  I guess, thinking about it looking at that picture, it's a case of machining a case back and then slotting a crystal into it.  I also suspect it's one of those where it's easy to explain but difficult to do well/right!

I have a watch for which I have been considering how good it would look with a clear back, hence my interest!

Cheers

Link to comment
Share on other sites

1 hour ago, MattWatch said:

Sorry, did you make that case back?  That looks incredible!  I guess, thinking about it looking at that picture, it's a case of machining a case back and then slotting a crystal into it.  I also suspect it's one of those where it's easy to explain but difficult to do well/right!

I have a watch for which I have been considering how good it would look with a clear back, hence my interest!

Cheers

The customer wanted to keep as much of the original case there as possible, as I recall this was the last case from a family watchmaking endeavor in the 80s. I opened it up and added the ring the crystal is fit into, it's press fitted into the back and the crystal if fitted in with a gasket. The movement they wanted to fit was significantly thicker than what was originally fitted. It probably would have been about the same work to make it up entirely from scratch.

Link to comment
Share on other sites



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • I think if you want to play Billy big b.ollocks then you have to have something up your sleeve, anyone that knows how to fight, plays dirty. Lets face it a lot of folk that voted for Brexit just rolled uk their sleeves to say up yours EU hoping for good changes. We have idiots for leaders and probably none of them clever enough to clean the shitty stick they were given. I didnt vote, what will be will be.
    • I voted leave too, my reasoning was the the EU is undemocratic, no elected officials. I don't regret it but I  am sad that both sides acted like petulant toddlers.  Shameful.  I'm not on other forums but if I was and left this site, would you shun me? Of course not, we aren't petulant toddlers.  
    • This is a type of tool that may be suitable to remove the bezel - though note that I'm pretty sure the watch should be face down - not face up, as in some of the photos of these tools on amazon & ebay! If you try one one of those, put the movement screws back in first to avoid accidents. https://www.amazon.co.uk/Removal-Professional-Remover-Watchmaker-Diameter/dp/B09XCH4QVN?source=ps-sl-shoppingads-lpcontext&ref_=fplfs&smid=A296NCMMFVXSDN&th=1  
    • Hi, I’m constantly asking my wife to help me with removing the stem in order to complete casing. To expand, this is not a challenge for me when the setting lever is secured by a screw (older calibers). However when the setting lever is attached to a spring loaded setting lever axel, like on more modern calibers, I simply don’t see how to apply enough pressure on the button to get the stem out short of putting the movement face down with the dial and hands attached, which I’m loath to do in order to avoid damaging the dial/hands? what technique should I be using? thanks  
    • Many thanks for your advice (being borne in mind at present) & offer Dell. When I was given the clock the plastic anchor was loose on the arbour (it had split at the 'hole') &, after repairing this, I have been trying to determine whether the spindle (pin) should be perpendicular when the pallet is sitting on a flat surface; or whether, when installed, its L-R extremes (or alternatively its tick & tock points) should lie at equal angles from the vertical when moved with spring absent. I can get the clock to run but in every such configuration the top block has to be turned anti-clockwise (from above) by quite a bit in order to be 'in beat' & it always runs fast (despite the pendulum being set to as slow as possible). This makes me wonder if there is any particular feature of/fault in a torsion spring clock which determines which turn direction (if any) is necessary to get it 'in beat'; & whether there would be a different set of settings that would get it running nearer to time at somewhere around the mid timing/inertia position which would then allow tweaking of the fast/slow setting.
×
×
  • Create New...