Jump to content

Panasonic G7


Recommended Posts

Panasonic G7 has its own native macro lens. It's a 30mm (So 60mm full frame equivelent). I use it as a regular prime though as I want to get in even closer with the camera further away.

The solution for me was a Viltrox EF-M2 speedbooster and Canon EF macro 100mm and 60mm prime lenses.

Both very sharp buy the 100mm is the most useful to me.

Shoot in 4k and use a 1080p timeline in Davinci Resolve and you will be able to crop in even further. Or shoot in 1080p and use the Ex-tele function on the G7 which effective turns your lens into two primes.

Side note - I recently upgraded to the GH5 and have not regretted it. But the G7 is an amazing camera so I decided to keep it - they compliment each other well.

Hope this helps.

Sent from my SM-G950F using Tapatalk

Link to comment
Share on other sites

4 minutes ago, Mark said:

Panasonic G7 has its own native macro lens. It's a 30mm (So 60mm full frame equivelent). I use it as a regular prime though as I want to get in even closer with the camera further away.

The solution for me was a Viltrox EF-M2 speedbooster and Canon EF macro 100mm and 60mm prime lenses.

Both very sharp buy the 100mm is the most useful to me.

Shoot in 4k and use a 1080p timeline in Davinci Resolve and you will be able to crop in even further. Or shoot in 1080p and use the Ex-tele function on the G7 which effective turns your lens into two primes.

Side note - I recently upgraded to the GH5 and have not regretted it. But the G7 is an amazing camera so I decided to keep it - they compliment each other well.

Hope this helps.

Sent from my SM-G950F using Tapatalk
 

Hi Mark, thanks for the info and prompt reply I'm looking forward to using it.

 

Many thanks

Kaz

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • So here is the new base, I made it so that the base will fit over and swallow the stump of the hand pusher tool (or at least my clone of the tool), I also reduced the OD of the bottom skirt a little as it looked a little large, here are a few pictures and the fake .pdf file which you need to convert to .zip once downloaded. The cut-out seen on the below image on the bottom of the base should swallow the OD (40 mm, +0.1 mm tolerance) of the stump and the height of the stump 9.5mm (measured to 9.1mm, but rounded to 9.5mm) - let me know if this works for your tool. Note, I think you may need to print supports for the new internal shelf created? Modular Movement Holder v2.pdf Modular Movement Holder v2.pdf
    • Hi Frank, you have dived headlong into the deep end. Hairspring work has to be the scariest thing a newbie has to tackle. Your hairspring appears to be bent and just putting it back into the regulator would not allow the balance to work properly. It might start oscillating but the performance would not be good. The proper thing to do is to unstud the hairspring, remove the hairspring from the balance, reinstall the hairspring on the stud carrier, reshape the endcurve and centre the collet to the balance jewel hole. This challenge would either make you or break you. Hope that you will be able to fix your watch. Welcome to the world of watchmaking. 
    • Have read of the Tech Sheet attached on the balance section page 12. It may be bent but until you reposition it back in the regulator pins you'll never know. Cheers CJ 4R35B_4R36A.pdf
    • Aloha All, My Seiko 4R35B movement stopped working today. Upon closer inspection, it looks like the balance spring came out of the regulator pin. This is my first time working on a balance. Any advice on how to get this spring repositioned (back to normal)? I'm pretty sure that while adjusting the beat error on this movement, I must have turned the stud (I didn't even know they turned), and the spring eventually fell out.  Will the spring go back to even spacing when it's back in the pin, or does it look bent? Thanks, Frank  
    • Good job, that band matches the watch perfectly.
×
×
  • Create New...