Jump to content

Vintage oilers - how do these operate?


Blubarb

Recommended Posts

I came across these vintage oilers and unsure of the markings and how to use.  There is an opening channel at the tip of the needle which I assume allows oil stored in the tube to flow.   

Thanks

IMG_3483.JPG

IMG_3484.JPG

IMG_3485.JPG

IMG_3486.JPG

Edited by Blubarb
Link to comment
Share on other sites

1 hour ago, oldhippy said:

They are called Glass Fountain Oilers.

 

Older watchmakers mostly use fountain oilers. They use the principles of capillary action to draw a small amount of oil out of the tube (like a fountain pen).

 

     not gravity or capillary,    with a rubber tube, in your mouth,  the was pushed oil into the jewel.  older jewelers concitered better than the pump style.   keep them,  they are valuable.  vin

  • Like 1
Link to comment
Share on other sites

Thank you for that helpful information that lead me to the NWCC Forum where I found this:  "To fill these oilers you need a small rubber hose that fits over the class tube. Place the hose on the end where the needle is,then place the other end in your oil bottle and suck on the hose. This will draw the oil into the glass tube. Don't fill the tube completely full. A small amount will last a long time. You can store the oiler laying flat in a dark place like a drawer of your watch bench."  Not sure how you "place the hose where the needle is...then place the other end in the oil bottle then suck on the hose"   I take this to mean suck on the glass tube to draw the oil into the tube? Agree? 

Edit:  Found this on WUS:  "In the past you could get glass "fountain" oilers. These are a blown glass tube with a very fine steel capillary in the end. They are about three inches long, and are filled by putting the tip down in an oil bottle and sucking on the open end of the tube. I have used these type oilers, but much prefer the control offered by a set of good dip oilers. "
 

Screen Shot 2018-11-13 at 10.46.12 PM.jpg

Edited by Blubarb
  • Like 1
Link to comment
Share on other sites

  • 5 years later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • So here is the new base (v 2.1), I made it so that the base will fit over and swallow the stump of the hand pusher tool (or at least my clone of the tool), I also reduced the OD of the bottom skirt a little as it looked/felt a little large, here are a few pictures and the fake .pdf file which you need to convert to .zip once downloaded.   The cut-out seen on the below image on the bottom of the base should swallow the OD (40 mm, +0.1 mm tolerance) of the stump and the height of the stump 9.5mm (measured to 9.1mm, but rounded to 9.5mm) - let me know if this works for your tool.   Note, I think you may need to print supports for the new internal shelf created? Modular Movement Holder.pdf  
    • Hi Frank, you have dived headlong into the deep end. Hairspring work has to be the scariest thing a newbie has to tackle. Your hairspring appears to be bent and just putting it back into the regulator would not allow the balance to work properly. It might start oscillating but the performance would not be good. The proper thing to do is to unstud the hairspring, remove the hairspring from the balance, reinstall the hairspring on the stud carrier, reshape the endcurve and centre the collet to the balance jewel hole. This challenge would either make you or break you. Hope that you will be able to fix your watch. Welcome to the world of watchmaking.  Watch this video. It think it'll give you an idea of the task ahead. From your 1st photo, I think you have a etachron type stud. Let me see if I can find a video on how to remove it from the arm.
    • Have read of the Tech Sheet attached on the balance section page 12. It may be bent but until you reposition it back in the regulator pins you'll never know. Cheers CJ 4R35B_4R36A.pdf
    • Aloha All, My Seiko 4R35B movement stopped working today. Upon closer inspection, it looks like the balance spring came out of the regulator pin. This is my first time working on a balance. Any advice on how to get this spring repositioned (back to normal)? I'm pretty sure that while adjusting the beat error on this movement, I must have turned the stud (I didn't even know they turned), and the spring eventually fell out.  Will the spring go back to even spacing when it's back in the pin, or does it look bent? Thanks, Frank  
    • Good job, that band matches the watch perfectly.
×
×
  • Create New...