Jump to content

3 things I've realized

phydaux
 Share

Recommended Posts

phydaux Watch Enthusiast

phydaux

Posted
Posted

So I'm slowly gathering tools & resources as money permits.  But as I read watchmaking books, watch youtube videos, and read this forum, four things have occurred to me:

1) When it comes to mechanical watches, until I get a proper cleaning station and a watch timing machine then I'm really just spinning my wheels.  There's just no point in trying to restore a watch if I haven't cleaned it, and until I get the watch up on the scope and check it for beat & time keeping then I don't really know if I have restored it or not.  

2) The vast majority of watches I'm going to run across, at flea markets and in family member's sock drawers, won't be mechanical.  They will be cheap quartz watches.  

3) The vast majority of watchmaking resources I've identified so far are for mechanical watches, not quarts watches.

So in light of those three things, I'm narrowing my initial focus, at least until I have a proper mechanical watch work bench set up, with a decent cleaning workstation and a timing machine.

 

By way of sharing the wealth, these are the quartz watch resources I've identified so far:

DVDs

A Course in Profits Through Service by Dan Gendron (out of production, but can be had on eBay)

BOOKS

Repairing Quartz Watches 
H.B. Fried

Mechanical and Quartz Watch Repair
Mick Watters

TOOLS

Quartz Watch Analyzer 

 

Any more would be highly appreciated.  Any if anyone had a recommendation an a watch analyzer, feel free to chime in.

Link to comment
Share on other sites
clockboy Distinguished Member

clockboy

Posted
Posted

Good tools, books and videos are all helpful but hands on practical work is where the learning really happens. Bits fly off into space never to be found again, you will break things, you will assemble in the wrong order, you will make lots of mistakes but with practice the mistakes become less frequent and the speed of dis-assembly and re-assembly quickens. For watches you need a timographer or the equivalent.

  • Like 1
  • Thanks 1
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • watchweasol
      Chronograph Pusher Rod for EB8371-67 Snapped and Stuck in Button. Can't Unscrew.

      By watchweasol · Posted

      Hi. Yes I get it , the slot in the end I’d to allow you to screw the button on whilst holding the pusher shaft. To remove the pusher tube you will need a tool such as the one shown by Richard. I think Ali Express the Chinese Amazon has replicas of the Horotec system for a lot less money, how effective they are not having had to use one. But as you said the way to go is complete removal and replacement, bodging it up will  lead to a repeat failure
    • JohnR725
      Notifications

      By JohnR725 · Posted

      It does look like it seems to be working again I'm getting emails.
    • JohnR725
      30T2 adjustment of timing washers

      By JohnR725 · Posted

      One of the things that I've been bothered with lately is timekeeping? For instance a 90-year-old pocket watch what so to timekeeping was it supposed to keep? They publish railroad timekeeping but I don't know how well normal non-railroad watches were supposed to keep time. The reason why the question comes up for me is I spend a lot of time at work adjusting watches to keep really really good time  because I have to please my boss where as when the watch was made I have to wonder what kind timekeeping would've been acceptable. After all they typically didn't have timing machines 100 years ago and they were timing and six positions certainly not for the non-railroad grade watch. On the other hand I do get paid by the hour so maybe I shouldn't be concerned of how much time I Spend trying to make everything keep chronometer timekeeping almost. Citing a Delta of 40 seconds for a 90-year-old watch is quite outstanding.
    • JohnR725
      Is this pallet fork over-locking?

      By JohnR725 · Posted

      That's an interesting question which I don't think I've seen explained anywhere. But I think the problem will go away just about instantaneously. In other words the  coating is really thin and it should go away almost immediately. So the problem should resolve itself extremely fast.  
    • VWatchie
      Is this pallet fork over-locking?

      By VWatchie · Posted

      I experienced that different types of shellac and their ages are affected differently by IPA. Sometimes the shellac dissolves in a few seconds and sometimes several minutes are required. Nowadays I never let shellac come into contact with IPA. It's a hotly debated topic here on WRT if you search. Like John, I don't think you need to worry about the weight of the shellac, but instead that it might start rubbing against something. When I learned how to adjust pallet stones, I tried documenting my experiences in this thread. Hopefully, it can help you. I personally don't believe in the idea of abrading the epilame before oiling so I don't think you need to think or worry about it. The only time I've heard anyone mention this is Alex on the YouTube channel Watch Repair Tutorials but actually no one else. I'm not saying it's "wrong" just that I don't think it's necessary or adds anything.
×
×
  • Create New...