Jump to content

Watch Batteries.


ecodec

Recommended Posts

Hi everyone, I realise that this is a purists forum but I fix all sorts of watches so I ask a question. 99% of the time I use Silver Oxide batteries for quartz watches, however I have noticed that when left for a long period flat, the battery may leak and rot and corrode the -ve terminal. Sometimes needing quite a repair. These batteries contain an alkaline electrolyte but due to the Sil Ox give a flatter voltage output they say. I have just performed a very basic test as follows on a new alkaline battery... Off load voltage 1.552 V,   Max current 2860 microamperes. About the same as the equivalent Sil Ox battery. I have not performed an extended test. Any constructive comments would be welcomed.

Edited by ecodec
correction
Link to comment
Share on other sites

This article has a lot of good information on this topic, including types and brands they found were less likely to leak: http://www.great-british-watch.co.uk/how-to-spot-and-deal-with-watch-battery-leaks/

I've just decided that whatever the benefits of silver oxide are, they are outweighed by the risk of using them, so I use lithium whenever I can. Whenever I can't, I replace them every three years or so, dead or not, and recommend that anyone I replace them for do the same. 

Link to comment
Share on other sites

One of the unfortunate problems of electric watches are the power source. Ever since they made the first electric timepiece the chemical battery is a problem. So for the most part sooner or later the batteries will all leak if you give them enough time.

3 hours ago, qhartman said:

I've just decided that whatever the benefits of silver oxide are, they are outweighed by the risk of using them, so I use lithium whenever I can. Whenever I can't, I replace them every three years or so, dead or not, and recommend that anyone I replace them for do the same

So I'm curious lithium batteries typically are physically sized differently then silver cells how do you deal with that? Then there is the other problem the voltage difference 1.55 versus 3 V?

 

 

Link to comment
Share on other sites

7 hours ago, qhartman said:

This article has a lot of good information on this topic, including types and brands they found were less likely to leak: http://www.great-british-watch.co.uk/how-to-spot-and-deal-with-watch-battery-leaks/

I've just decided that whatever the benefits of silver oxide are, they are outweighed by the risk of using them, so I use lithium whenever I can. Whenever I can't, I replace them every three years or so, dead or not, and recommend that anyone I replace them for do the same. 

Thank you qhartmann for your help, Mike. ECODEC.

Link to comment
Share on other sites




So I'm curious lithium batteries typically are physically sized differently then silver cells how do you deal with that? Then there is the other problem the voltage difference 1.55 versus 3 V?
 
 


Doh. I was thinking of alkaline vs silver oxide when I dashed that off. It would be nice if lithium were an option, but as far as I know unless the watch is designed for it, it isn't for the reasons you state. Sorry my haste let some misinformation get out.

Sent from my ONEPLUS A5000 using Tapatalk

Link to comment
Share on other sites

10 hours ago, qhartman said:

This article has a lot of good information on this topic, including types and brands they found were less likely to leak: http://www.great-british-watch.co.uk/how-to-spot-and-deal-with-watch-battery-leaks/

I've just decided that whatever the benefits of silver oxide are, they are outweighed by the risk of using them, so I use lithium whenever I can. Whenever I can't, I replace them every three years or so, dead or not, and recommend that anyone I replace them for do the same. 

Thank you Sir. Ecodec.

 

Edited by ecodec
more info
Link to comment
Share on other sites

Hi Guys   I think the moral of this story is never store quartz  watches or clocks with batteries in as all batteries given time will leak causing damage, best to remove the battery and fit a label as to what type it takes then its easy to pop one in when you want to wear it. saves scratching the head trying to remember what was fitted.

  • Like 1
Link to comment
Share on other sites



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • people be honest.... Swatch is evil for the watchmakers and repairers, BUT not everything in watches from Switzerland is from the Swatch-Group. As far as i know, Selitta got sacked by Swatch as a Movement-Assembler for them and they started to produce Movements in their own Name with slight Modifications. As far as i know, they sell Parts to the Market for their Movements. In most cases, if a ETA-Movement fails, it is a valid Option to replace it with a Selitta Movement, which i consider the Solution for this Mess with the Swatch-Group...... I have no Connection to anybody at Selitta, but being a Swiss-Guy, i still like to have Swiss-Made Watches, but not from the Swatch-Group.   ok ? regards, Ernst
    • Just one more greedy act by Swatch. They started a number of years ago here in the US..cutting off supplies to watchmakers that could build complications that many Swatch houses couldn't even touch. Old school masters who had gone through some of the most prestigious houses in the world. Otto Frei has some statements on their page about it. I tell all my customers to avoid new Swiss watches like the plague,..unless they just want an older one in their collection that still has some parts out on the market, or they have really deep pockets and don't mind waiting months and paying through the nose to get it back. Plenty of others to choose from..IE Seiko,..or other non-swiss brands Even a number of Chinese brands are catching up with the Swiss,..and I think that in time, their actions will be their downfall
    • Yes. If that's not what you are experiencing...start looking for something rubbing. A 1st guess is that one of the hands is rubbing against the hole in the center of the dial. Especially if you now have lower amplitude in face up/ face down positions.
    • Once a movement has the dial and hands put back and it is recased, would you expect the assembled watch to have the same amplitude as when the movement is in a movement holder and is without hands and dial? Thanks
    • C07641+ not sure what the "+" is for after the last digit.
×
×
  • Create New...