Staking Tools & Jewel Setting Tools
Discussing Staking Toolkits and Jewel Setting Tools and Kits
95 topics in this forum
-
- 53 replies
- 4.8k views
-
- 7 replies
- 621 views
-
- 9 replies
- 618 views
-
- 5 replies
- 558 views
-
- 8 replies
- 1.3k views
-
- 109 replies
- 39k views
-
- 381 replies
- 120.7k views
-
- 5 replies
- 533 views
-
- 39 replies
- 13.6k views
-
- 25 replies
- 1.6k views
-
- 1 reply
- 435 views
-
- 7 replies
- 587 views
-
- 6 replies
- 636 views
-
- 9 replies
- 1.2k views
-
- 0 replies
- 584 views
-
- 3 replies
- 841 views
-
- 35 replies
- 5.9k views
-
- 11 replies
- 1.3k views
-
- 3 replies
- 1k views
-
- 0 replies
- 816 views
-
- 19 replies
- 2.3k views
-
- 2 replies
- 2.5k views
-
- 5 replies
- 1.4k views
-
- 17 replies
- 6.7k views
-
- 5 replies
- 2.1k views
.thumb.jpg.cb17a66989f1e796fd4217db2e9ca9df.jpg)
-
Topics
-
-
Posts
-
Glad to see it's working. Have you gone for the 40MX or 6M40 crown? -
typically when people use a demagnetizer they like to do the entire watch. You will note that the balance wheel has to be removed first as it has magnets on it. So I was urging a caution of not to demagnetize the completely assembled watch. Then some electric watches have additional magnets other than on the balance wheel itself. Another reason to be cautious with electric watches. -
Taken from the manual..
-
I realized the OP had a 9150, the stop lever being underneath and not on top of the setting lever jumps out at you. The servicing is more or less the same though. -
interesting strategy for an electric watch which typically will have permanent magnets that really don't like to be demagnetized even if they are listed as permanent. typically I've given up with that question because it's wishful thinking that anyone would have test equipment beyond the DVM. Test equipment for electric watch would be a variable voltage power supply, some way of measuring microamp current and a DVM for resistance and voltage. while they look almost identical at least to the casual observer I don't think this is a 9154 which is why attached the technical up above for 9150. But to be thorough I will attach the technical for the 9154 and some images I found on the Internet so 9150 as for contacts for the coil assembly with one home attached to a screw. than the 9154 only has three contacts the 9154 as a different coil arrangement were now it only has three terminals none of which are attached to the screw. So the image down below of this watch is a 9150. Although not the same all of the cleaning procedures testing etc. will all be identical other than the coil resistances current consumption will probably be a little bit different. yes the joys of YouTube watch repair where nobody ever reads the tech sheet and is unaware of the impending doom that they typically never have but anyone following will. Yes you definitely want to look at the tech guide before you even begin the disassemble or it will be not a happy outcome. if you are hoping for a quick squirt of lighter fluid and the watch would run I think you're out of luck. Electric watches typically have very little power and require the gear train to be extremely free moving in other words no sticky oil at all. in addition to when people change batteries it's very bad to get anything like old battery corrosion or anything else into an electric watch. So basically no quick fix here. 3540_ETA 9154.pdf
-
