What is this tool? How do I use it? Tools Identification
Have a watch repair tool and unsure what its used for or how to use it - post here.
138 topics in this forum
-
- 0 replies
- 1.2k views
-
- 16 replies
- 1.9k views
-
- 3 replies
- 1.1k views
-
- 1 reply
- 429 views
-
- 5 replies
- 870 views
-
- 6 replies
- 839 views
-
- 0 replies
- 356 views
-
- 4 replies
- 748 views
-
- 5 replies
- 823 views
-
- 2 replies
- 560 views
-
- 1 reply
- 617 views
-
- 17 replies
- 1k views
-
- 1 reply
- 373 views
-
- 5 replies
- 1k views
-
- 4 replies
- 1.2k views
-
- 0 replies
- 483 views
-
- 9 replies
- 969 views
-
- 2 replies
- 723 views
-
- 5 replies
- 953 views
-
- 11 replies
- 1.2k views
-
- 12 replies
- 1.1k views
-
- 9 replies
- 956 views
-
- 7 replies
- 1.2k views
-
- 26 replies
- 1.6k views
-
- 6 replies
- 1.2k views
.thumb.jpg.e1737221d1bb91b37331a627546ff250.jpg)
-
Topics
-
-
Posts
-
So here is the new base (v 2.1), I made it so that the base will fit over and swallow the stump of the hand pusher tool (or at least my clone of the tool), I also reduced the OD of the bottom skirt a little as it looked/felt a little large, here are a few pictures and the fake .pdf file which you need to convert to .zip once downloaded. The cut-out seen on the below image on the bottom of the base should swallow the OD (40 mm, +0.1 mm tolerance) of the stump and the height of the stump 9.5mm (measured to 9.1mm, but rounded to 9.5mm) - let me know if this works for your tool. Note, I think you may need to print supports for the new internal shelf created? Here is the fake .pdf for just the FreeCAD base file and 3mf files Modular Movement Holder.pdf Here is the fake pdf for complete set of the new base and ring FreeCAD/3mf files: Modular Movement Holder base and ring v 2.1.pdf -
By HectorLooi · Posted
Hi Frank, you have dived headlong into the deep end. Hairspring work has to be the scariest thing a newbie has to tackle. Your hairspring appears to be bent and just putting it back into the regulator would not allow the balance to work properly. It might start oscillating but the performance would not be good. The proper thing to do is to unstud the hairspring, remove the hairspring from the balance, reinstall the hairspring on the stud carrier, reshape the endcurve and centre the collet to the balance jewel hole. This challenge would either make you or break you. Hope that you will be able to fix your watch. Welcome to the world of watchmaking. Watch this video. It think it'll give you an idea of the task ahead. From your 1st photo, I think you have a etachron type stud. Let me see if I can find a video on how to remove it from the arm. -
Have read of the Tech Sheet attached on the balance section page 12. It may be bent but until you reposition it back in the regulator pins you'll never know. Cheers CJ 4R35B_4R36A.pdf -
By Hawaiikook808 · Posted
Aloha All, My Seiko 4R35B movement stopped working today. Upon closer inspection, it looks like the balance spring came out of the regulator pin. This is my first time working on a balance. Any advice on how to get this spring repositioned (back to normal)? I'm pretty sure that while adjusting the beat error on this movement, I must have turned the stud (I didn't even know they turned), and the spring eventually fell out. Will the spring go back to even spacing when it's back in the pin, or does it look bent? Thanks, Frank -
Good job, that band matches the watch perfectly.
-
