Watch Repairs Help & Advice
SECTION RULES
If you are a new member, we would consider it polite for you to introduce yourself here before posting your questions.
Subforums
-
- 2.6k
- posts
-
New to watch repair ** Safe Zone For Learner Watch Repairers **
Discussing subjects relating to learner watch repairers.
More experienced repairers - please guide learners with patience and respect
- 5.1k
- posts
-
- 2.2k
- posts
-
- 3.9k
- posts
-
- 922
- posts
-
- 1.8k
- posts
-
- 1.8k
- posts
-
- 1.3k
- posts
-
- 804
- posts
-
- 749
- posts
-
- 1.7k
- posts
-
- 2.7k
- posts
-
- 329
- posts
8959 topics in this forum
-
- 0 replies
- 4.2k views
-
- 5 replies
- 126 views
-
- 2 replies
- 998 views
-
- 5 replies
- 488 views
-
- 15 replies
- 2k views
-
- 3 replies
- 821 views
-
- 0 replies
- 173 views
-
- 1 reply
- 235 views
-
- 6 replies
- 745 views
-
- 4 replies
- 583 views
-
- 2 replies
- 392 views
-
- 5 replies
- 580 views
-
- 1 reply
- 997 views
-
- 2 replies
- 516 views
-
- 0 replies
- 396 views
-
- 0 replies
- 442 views
-
- 0 replies
- 446 views
-
- 3 replies
- 555 views
-
- 0 replies
- 744 views
-
- 8 replies
- 2.3k views
-
- 0 replies
- 496 views
-
- 0 replies
- 464 views
-
- 2 replies
- 569 views
-
- 2 replies
- 500 views
-
- 3 replies
- 725 views
-
Topics
-
-
Posts
-
I missed this earlier. The dial isn't going into the holder, it should sit proud of it. This is what I am currently using which I print for each different movement. -
By Neverenoughwatches · Posted
I didn't think pulling to set position would work harden the spring, in that position it is stressed where the arm starts. By work hardening i meant rapid polishing at that point, a bit like polishing a pivot work hardens as it compresses the steel. I doubt polishing by hand would achieve much in that respect though. Its finished, arm polished up mostly at the join to the bridge's main body. I'm ok with it, the screw holes aren't great as i had to open them up by redrilling and positioning it was difficult, I'm not much use with a loupe, opening up with a file might be a better option for me or i could just use the correct drill size 😅. And the detent is way too deep, i had to guess that with the stem release out of position and sat on top, but i only took one measure and went for it, no slowly slowly catch your monkey 😅. First go I'm happy , well sort of, it works and thats a big thing for me, next one will have a bit more finesse. Anyone thats interested, after filing, i used a 2000 grade home made diamond micro file and then 20 micron film, the film is much better than wet and dry, more stable to use and doesn't shed cheap grade grit everywhere , then auto polish on a sponge pad. -
By RichardHarris123 · Posted
I'm assuming that every time you set the watch you are work hardening the detent spring, maximum hardening is where it meets the plate due to maximum deflection. That's why it snaps there. The Young's modulus may be the same but after it's reached its maximum yeid strength it breaks. My mechanic engineering is very rusty, correct me if I'm wrong. -
By Neverenoughwatches · Posted
Ah ok yes that makes sense to polish it where the arm starts to form from the body of the bridge, i thought you meant the underneath of all the arm. -
this is something I've never quite understood about the some of the Swiss companies. In 1957 Omega was using 9010 for the keyless parts with epilam. there's been a slow migration towards using heavier lubrication's but still typically oils and epilam to keep them in place. When it seems like 9504 works so much better.
-
