Jump to content
  • The watch repair course and videos section has moved - if you are a Patron via Patreon or a WRT Subscriber, kindly create an account here: https://www.watchrepairlessons.com, if you have not done so already, in order to continue with your access to the Early Access and Ad-Free videos.

    The Patron and Subscribers section in the WatchRepairLessons.com dashboard (direct link) will detail all your subscription details. 

    This will help me consolidate all my videos under one roof rather than maintaining two separate systems, and it will also help clean up WRT a bit.

    If you have any questions please message me, Mark :)

Your Watch Collection

Show us what you are wearing today, or any watch in your collection - or even show off your whole watch collection. What watches have you purchased recently? :)

707 topics in this forum

    • 7 replies
    • 2,274 views
  1. Casio

    • 1 reply
    • 437 views
  2. My collection

    • 6 replies
    • 584 views
    • 8 replies
    • 630 views
    • 5 replies
    • 1,118 views
    • 0 replies
    • 526 views
    • 6 replies
    • 1,086 views
  3. Volga Watch

    • 1 reply
    • 1,686 views
    • 7 replies
    • 1,420 views
    • 4 replies
    • 1,083 views
  4. a few of my watches

    • 3 replies
    • 1,244 views
    • 5 replies
    • 2,288 views
  5. Excalibur

    • 5 replies
    • 1,137 views
  6. Identify mov.t?

    • 5 replies
    • 1,386 views
    • 15 replies
    • 2,322 views
  7. 1894 Elgin 6S

    • 3 replies
    • 1,257 views
  8. A simple complication. 'Mondia Top-second'

    • 6 replies
    • 3,323 views
    • 3 replies
    • 2,105 views
    • 0 replies
    • 1,155 views
  9. 1897 Elgin 6S, 7J

    • 3 replies
    • 1,394 views
    • 8 replies
    • 6,008 views
    • 4 replies
    • 2,356 views
    • 10 replies
    • 4,747 views
  10. Camerer Cuss & Co / Rolex

    • 2 replies
    • 2,338 views
  11. Finishing movements

    • 3 replies
    • 1,977 views
  • Recent Topics

  • Posts

    • I'm trying to get my old grandfathers Automatic Seiko up running and I took the movement out of the case today. I figure I will replace the mainspring and I was not able to salvage the o-ring gasket on the stem nor the case back gasket. I don't know if they're supposed to be flat and quite hard. Anyway, the just crumbled apart when I tried to remove them and the case back one had to be removed to get the movement out. My question now is where, or rather how, do I source these parts. I've been searching cousins and they have a lot of parts and I also found an old article in this forum that pointed me to Jules Borel site but it was out of stock there.  Is there some sort of generic gaskets I may use ? What measurements should I use when searching for new ones ? Where may they be found ? It would seem that one of the trickier obstacles with this hobby is sourcing new parts, especially when one can only afford to tinker with OLD movements. On the back it says Seiko 7005-7011 but it sure looks a lot like 7005-7010 I've seen around here. Thanks!
    • Welcome to the forum. 
    • Hi, All my life I've been interested in watches of all kinds. I started watching videos about watch repairing on YouTube and ended up taking Mark's online course. Before I new it I had bought some tweezers and two China versions of the UNITAS 6497 to tinker with. Great Fun ! Hope I'll see you around /P
    • I don't think that microscopic difference matter that much, and not even that they are so pronounced when going from a watch brand to another as someone suggested. While it's a fact that generally speaking Swiss screw slots are narrow than Japanese for a same width, I suppose the parallel drivers makers have calibrated well the blade thickness to be the best average size.  For me the metric isn't just that. A very important aspect is the ability to grip well for the initial turn on long screw that has just put on its place, always tilted. on one side by some amount.  Since I don't think there are available videos about that I will make a comparison one as soon I have the opportunity, and update this thread. 
    • To quote measuretwice from a previous posti g: In the common vernacular, hollow ground is used to describe the resulting parallel No matter how many years one has done something is always good to try to understand what others mean. Searching the Internet alsio helps https://toolguyd.com/lee-valleys-parallel-tip-screwdrivers/
×
×
  • Create New...