Your Walkthroughs and Techniques
Post descriptive walkthroughs of watches you have stripped down and serviced and/or repaired, parts you have made or techniques you wish to share.
This is an interesting section where we post our challenges and how we have over-come them. You can also post walkthroughs and share your techniques.
SECTION RULES
This section is strictly for those posting real step-by-step walkthroughs of actual repair or servicing techniques relating to watch repair and/or horology in general. The idea is that we help each other by describing or sharing our repair techniques, or telling a story of how we have progressed.
If you are not posting step-by-step walkthroughs, such as - you would just like to showcase a completed repair job, then please choose a more appropriate sub-forum for your content. If your post is not deemed to be a legitimate walkthrough then a moderator will move your post to the appropriate section without notice. Thank you for your co-operation.
- You must be a member with at least 10 posts on the forum in order to contribute in this section
365 topics in this forum
-
- 35 replies
- 25.1k views
-
- 64 replies
- 24.3k views
-
- 24 replies
- 23.8k views
-
- 52 replies
- 23.2k views
-
- 36 replies
- 22.8k views
-
- 14 replies
- 20.9k views
-
- 19 replies
- 20.9k views
-
- 72 replies
- 20.8k views
-
- 16 replies
- 20.4k views
-
- 58 replies
- 19.9k views
-
- 12 replies
- 19.7k views
-
- 33 replies
- 19.7k views
-
- 12 replies
- 19.4k views
-
- 20 replies
- 18.9k views
-
- 9 replies
- 18.8k views
-
- 24 replies
- 18.7k views
-
- 6 replies
- 18.6k views
-
- 31 replies
- 18.5k views
-
- 6 replies
- 18.3k views
-
- 29 replies
- 18.3k views
-
- 14 replies
- 18k views
-
- 31 replies
- 17.6k views
-
- 54 replies
- 17.5k views
-
- 53 replies
- 17.2k views
-
- 16 replies
- 16.9k views
-
Topics
-
-
Posts
-
That could work - two blunt pressure points would spread out the force required in order to reduce damage, and two small pins should fit slightly angled through the inner coil of the spring. I was thinking about this while working on other chores and had a crazy thought when I saw a can of expanding rigid sprayable foam, but who'd want to have to clean out the barrel and spring after that? -
That's very observant of you, Nev & that the 4th wheel is from another movement & has been dished to fit does seem a more likely explanation. Thanks for the education re calculating the rate & spring frequency. In the meantime, spurred by your earlier comnent, I risked a further tinker with the balance spring, cleaning it, fully un-kinking the last few cms (I'd been worried about breaking it first time round) & pinning it at the very end. The clock now seems to be running slow when the regulator is in that position so some progress at last.....Many thanks, once again! -
By rjenkinsgb · Posted
Snap! I recently finished my Gruen 510 movement - though the case for mine is in a rather sad state; I'm going to try re-plating it (in nickel, it's not a gold one). Re. the screws, I got a few of the one gram mixed batches from ebay. I've only needed a couple of screws for things so far, both rare, minuscule types - but both in the mix, after enough time sorting through them! The ones such as normal bridge screws are quite common in those lots. -
By rjenkinsgb · Posted
Two pins or screwdrivers angled out slightly, pressing through from the barrel centre from the opposite side so they contact just clear of the hole in the lid? eg. Strap pin driver needles or similar. -
That's a good idea - shrinking down the nut and wrench size from the old casebook trick!
-
