Jump to content

Seiko 6117 mainplate

rogart63
 Share

Recommended Posts

rogart63 Distinguished Member

rogart63

Posted
Posted

Trying high and low to find a new mainplate for a 6117 . The old one was very badly worn in the barrel arbor. Tried to do a bushing for it but failed. So now i am trying to find a better one. As i said i have tried to locate one but have run out of options. Anyone got a tips where i could search for Seiko parts. Besides Ebay. A 6105 mainplate would work also. 

Link to comment
Share on other sites
rogart63 Distinguished Member

rogart63

Posted
  • Author
Posted
 

Sorry I can't find a replacement plate. What happened with the repair.

The lower barrel hole was so worn that the mainspring barrel was riding on the plate. Tried to ream it and putting in a jewel. But because the hole was worn  the reamer did go sideways and the hole ended up in the wrong place. And the back of the mainplate had two different thickness where the barrel hole is. So making it extra hard to make a bigger hole.   So have to replace it. 

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • TheQuietMan
      Help please.

      By TheQuietMan · Posted

      Ok thanks Ross, I will give that a try!😁
    • rossjackson01
      Intro

      By rossjackson01 · Posted

      Welcome my friend. 
    • rossjackson01
      Help please.

      By rossjackson01 · Posted

      Been there. Worn that Tshirt.  'ping'. Hands and knees. Nothing. Nada. 20 minutes? Ha! I found it 7 month later. How? Well, after advice from a member, I invested in a £4 UV light torch.  Hands and knees looking for a 'ping' from a Sekonda, found them both within 30 seconds. UV makes the jewel shine. easy peasy. Could have taken longer. Just lucky on the location of the search. Hope this helps.
    • Rixy
      Broken lug

      By Rixy · Posted

      Thanks Dell. I thought about silver soldering. Have never done it but would like to give it a go. Do you think to put flux on the butted joint then run the solder in or to maybe brace it with a piece of scrap spring steel?
    • rossjackson01
      Without Our Forum

      By rossjackson01 · Posted

      Never and others. Yes, like you I do spend a fair amount of time reading the contents of this forum. I find it better that any other. Clear, lucid, no Prima Donas, and most of all an easy access without adverts. All thanks to Mark. God bless you mate. You give so much to many of us. What if? No Mark? Hypothetically. A forum. I did run a forum for a few years. Really enjoyed it, but became so engrossed that it did affect my health. I gave to to others to run. Not been back. It was very successful and rivalled a number of large paying sites. No adverts, no others but me. I did ask and listen to members comments and it worked well.    Costs Having a domain name, £10 annually.  Register the site with a forum company, free. Build the site using the forum company guide lines, free. It looked and ran almost the same a Mark's. All the same facilities. The cost was only £5 per month, but counted visits (views). If I recall, it was that price for 5,000 views. Each extra 5,000 views increased the price by £2 per month. Success was my own personal undoing. From £5 per month initially, it rose to £60 a month and looked like increasing. This was 10 years ago. I could not afford that, and asked it anyone would like to take over and someone did. I would assume that this is the price that Mark is funding for us all. His return is our continued comments on the internet about his course, and the fact that many of the big names on YouTube mention him as their Tutor. Those of us who have done, and are still using, his course, benefit. In comparison to other courses, I can't believe how cheap it is, and the value is exceptional. It is the structure that gives the value. Long may Mark reign. Ross  
×
×
  • Create New...