Jump to content

Omega dial


antonyh

Recommended Posts

Well i could`nt resist it another Omega that needs to be done up, i won`t go into it all.

The picures are not the best, but anyway dial as it arrived,

dial after i cleaned it up just to see what it looked like, with another set of tempary hands, awfull i know.

i had polished the case up, to give it a bit of a shine, i was going to get someone to restore the dial, but prices have sky rocketed

the last few years.

so in a drunked state last night i thought i`d have a go.

omegabefore.jpg

 

 

Beforedial1.thumb.jpg.703f256319286f12dfc0f588ad45aeb0.jpg

 

 

 

Bluedial.jpg

 

Edited by antonyh
pictures wrong order
  • Like 2
Link to comment
Share on other sites

Hey, that's not bad, pictures a little unclear and I'm not certain what that dial was suppossed to look like, but I'd say I've deffinately seen worse dial jobs. what were your methods/paints? Did you remove the batons and logo or cover them somehow? 

Link to comment
Share on other sites

Well firsty, don`t do it after you`ve been drinking.

The hardest thing i had to get over was finding a spray paint with a fine spray of paint, i tried loads before i found one.

I just kept cleaning the dial, with thinners then i used a a brush to finish it.

i did not remove the batons, i just gave it a couple of passes with the can.

after an hour before the paint had fully hardened i just simply removed the paint from the batons.

Its not purfect but it makes it a bit more wareable than before, and its i know its supposed to have a black dial with delphine hands,,,,,,,,,,, one day..

  • Like 1
Link to comment
Share on other sites

Well It seems like you could always go back and re do it if you wanted to, the dial as it was looked pretty aweful in my opinion, though i wouldn't be surprised if someone disagreed with me I think most of us would agree that it had gone well past a 'patina'. 
 

Edited by Ishima
Link to comment
Share on other sites

Well i`ve done what i set out to do, i`ve changed the hands to something a bit more inkeeping ,i`ve filled in the end of the battons

with luminious paint as it should be , and i`m going to where it, ive since changed the seconds hand for a chrome one to match.

In the old days i would have had it restored, it its not worth the £200 + V Soni wanted last time i asked the to do a dial for me.

omegabluedial.jpg

Link to comment
Share on other sites

  • 2 weeks later...

Dial looks a bit stark, probably the lack of minute markers doesn't help.

I would experiment and try to have a cross hair to break up the dial. Either use a sharpie, or even scribe the croshairs into the dial back to the metal with a sharp blade.

My 2cents.

Anilv

  • Like 1
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Two pins or screwdrivers angled out slightly, pressing through from the barrel centre from the opposite side so they contact just clear of the hole in the lid? eg. Strap pin driver needles or similar.
    • That's a good idea - shrinking down the nut and wrench size from the old casebook trick!
    • I missed this earlier. The dial isn't going into the holder, it should sit proud of it. This is what I am currently using which I print for each different movement.    
    • I didn't think pulling to set position would work harden the spring, in that position it is stressed where the arm starts. By work hardening i meant rapid polishing at that point, a bit like polishing a pivot work hardens as it compresses the steel. I doubt polishing by hand would achieve much in that respect though. Its finished, arm polished up mostly at the join to the bridge's main body. I'm ok with it, the screw holes aren't great as i had to open them up by redrilling and positioning it was difficult, I'm not much use with a loupe, opening up with a file might be a better option for me or i could just use the correct drill size 😅. And the detent is way too deep, i had to guess that with the stem release out of position and sat on top, but i only took one measure and went for it, no slowly slowly catch your monkey 😅. First go I'm happy , well sort of, it works and thats a big thing for me, next one will have a bit more finesse.  Anyone thats interested, after filing, i used a 2000 grade home made diamond  micro file and then 20 micron film, the film is much better than wet and dry, more stable to use and doesn't shed cheap grade grit everywhere , then auto polish on a sponge pad.
    • I'm assuming that every time you set the watch you are work hardening the detent spring, maximum hardening is  where it meets the plate due to maximum deflection.   That's why it snaps there.  The Young's modulus may be the same but after it's reached its maximum yeid strength it breaks.  My mechanic engineering is very rusty, correct me if I'm wrong. 
×
×
  • Create New...