Jump to content

Greetings from Santa Cruz, California

redbat

By redbat
in Introduce Yourself Here

 Share

Recommended Posts

redbat New Member

redbat

Posted
Posted

Hello all,

I've been lurking here since 2015, but this is my first post.  

I've been interested in watches for a few years now and am now considering taking some time off of work to take the BHI distance learning courses in the hopes of making a career of watch and clock repair as an independent.

I've been acquiring tools and information for a while, and recently learned how to disassemble and reassemble a 6497 movement in preparation for the SAWTA course at the Watch Technology Institution admission test at North Seattle College.  I have recently come to the conclusion that I cannot make the move to Seattle for 2 years to attend the program, which is why I am now considering the BHI courses.

My most recent repair has been to my Maktime (Poljot) 3133 chronograph; the glass had gotten cloudy on the inside, so I had removed the movement from the case to clean the glass, and made the rookie mistake of not inserting the stem correctly, which meant removing the calendar works to reset the keyless works.  In the process of doing this, I did not correctly replace the date indicator driving wheel, which uses a small hooked wire connected to a planetary gear inside the driving wheel to move the teeth of the date wheel.  Figuring out how to adjust this correctly and reassembling the watch with a working date wheel was a wonderful feeling.

Anyway, apologies for the novel, and I'm looking forward to participating in the forum!

Link to comment
Share on other sites
dadistic Distinguished Member

dadistic

Posted
Posted (edited)

Greetings, thanks for the introduction.

It's too bad that you can't attend the school in Seattle. I think that having access to modern (and expensive) tools and equipment, along with the instructors to demonstrate how to use them, is invaluable. Especially if you are planning on making a career of this. 

But, I agree, pulling up stakes is hard. I can't do it either, at my age I'd never recoup the investment. But who knows? I may do it anyway :)

Edited by dadistic
Noticed your location
Link to comment
Share on other sites
RyMoeller Super WRT Addict

RyMoeller

Posted
Posted

Hello and welcome to the forum.

Nice job sorting out the Poljot issue.  In this line of work there is much to be learned from mistakes provided you're disinclined to throw in the the towel. 

What a great idea to take the BHI courses- that's something I should probably look into also.  I've heard about the courses offered up in Washington and I think also in Texas or Oklahoma but like you, packing up and moving isn't really an option right now.  Hopefully things will work out in your favor to keep you on your desired schedule. 

Great profile image by the way.  I just love flying foxes.  :biggrin:

Link to comment
Share on other sites
Vich Distinguished Member

Vich

Posted
Posted

Hello Redbat,

had to smile when I read your lead in. In the past I have also made all those sort of mistakes, in fact I would hazard a guess that lots of us have but philosophy jumps in to say mistakes are just lessons learned. Expletives also help in the moments after such lessons are learned of course

Welcome from me

Cheers,

Vic

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Hawaiikook808
      Balance spring fell out of regulator pin.

      By Hawaiikook808 · Posted

      Thank you so much, Hector and CJ. I appreciate the tech sheet and the video. Gasp, I think I will make the attempt. What's the worst that can happen? I think there may be a new balance complete in my future, though.  I'll update the post and let you know the result. R, Frank  
    • Waggy
      Movement holder made with 3D printer

      By Waggy · Posted

      So here is the new base (v 2.1), I made it so that the base will fit over and swallow the stump of the hand pusher tool (or at least my clone of the tool), I also reduced the OD of the bottom skirt a little as it looked/felt a little large, here are a few pictures and the fake .pdf file which you need to convert to .zip once downloaded.   The cut-out seen on the below image on the bottom of the base should swallow the OD (40 mm, +0.1 mm tolerance) of the stump and the height of the stump 9.5mm (measured to 9.1mm, but rounded to 9.5mm) - let me know if this works for your tool.   Note, I think you may need to print supports for the new internal shelf created? Here is the fake .pdf for just the FreeCAD base file and 3mf files Modular Movement Holder.pdf Here is the fake pdf for complete set of the new base and ring FreeCAD/3mf files: Modular Movement Holder base and ring v 2.1.pdf However, I'm wondering how often you could use this feature, adding the dial usually increases the OD of the movement, so you would need a new (larger) adapter ring tuned to the OD of the dial and I wouldn't like to grip the dial in any kind of movement holder if It could be avoided for fear of damaging it. Maybe I'm misunderstanding you?
    • HectorLooi
      Balance spring fell out of regulator pin.

      By HectorLooi · Posted

      Hi Frank, you have dived headlong into the deep end. Hairspring work has to be the scariest thing a newbie has to tackle. Your hairspring appears to be bent and just putting it back into the regulator would not allow the balance to work properly. It might start oscillating but the performance would not be good. The proper thing to do is to unstud the hairspring, remove the hairspring from the balance, reinstall the hairspring on the stud carrier, reshape the endcurve and centre the collet to the balance jewel hole. This challenge would either make you or break you. Hope that you will be able to fix your watch. Welcome to the world of watchmaking.  Watch this video. It think it'll give you an idea of the task ahead. From your 1st photo, I think you have a etachron type stud. Let me see if I can find a video on how to remove it from the arm.
    • Curare
      Balance spring fell out of regulator pin.

      By Curare · Posted

      Have read of the Tech Sheet attached on the balance section page 12. It may be bent but until you reposition it back in the regulator pins you'll never know. Cheers CJ 4R35B_4R36A.pdf
    • Hawaiikook808
      Balance spring fell out of regulator pin.

      By Hawaiikook808 · Posted

      Aloha All, My Seiko 4R35B movement stopped working today. Upon closer inspection, it looks like the balance spring came out of the regulator pin. This is my first time working on a balance. Any advice on how to get this spring repositioned (back to normal)? I'm pretty sure that while adjusting the beat error on this movement, I must have turned the stud (I didn't even know they turned), and the spring eventually fell out.  Will the spring go back to even spacing when it's back in the pin, or does it look bent? Thanks, Frank  
×
×
  • Create New...