Jump to content

Seiko 7005-2000


Recommended Posts

1 hour ago, rogart63 said:

Yepp. You need a sharp knife. Like a breakable knife?

 

Thanks rogart63 I'm looking forward to this then, NOT

i must say this forum is the best why bother going on others,the chaps are so helpful, knowledge of 1000 years oldhippy has most of them :D

Link to comment
Share on other sites

On 3/17/2017 at 4:31 PM, BUSAKAZ said:

Hi all, does anyone know how to remove the main spring out of the barrel as I need to replace it.

Please tell, how do you know that you need to replace the mainspring? It has broken?

Link to comment
Share on other sites

1 hour ago, jdm said:

Please tell, how do you know that you need to replace the mainspring? It has broken?

I just wanted to check that it wasn't broken in fact it looks pretty clean no gunge inside a dog to open though.

Link to comment
Share on other sites

Just now, BUSAKAZ said:

I just wanted to check that it wasn't broken in fact it looks pretty clean no gunge inside a dog to open though.

That's because Seiko barrels are not meant to be opened or the mainspring replace, and if not broken are better left alone.

Link to comment
Share on other sites

44 minutes ago, BUSAKAZ said:

The watch wasn't working elts I would have done that first.

To check if barrell / mainspring are OK just remove the pallet fork and click. With one or two turns of the ratchet, the train must spin fast. No need to open the barrel.

Link to comment
Share on other sites

To check if barrell / mainspring are OK just remove the pallet fork and click. With one or two turns of the ratchet, the train must spin fast. No need to open the barrel.

Is that just newer models or something? In my limited tinkering I've opened a few barrels up to have a look, and am currently hunting down a mainspring winder so that I can get the mainspring out and clean and oil them and put them back without knackering them! I know Seiko don't recommend it but for a vintage piece I had kind of gathered that it was part of doing a proper service.

 

*Edit: the 7005 is not a new movement so I'm honestly interested to hear what the verdict is

[emoji848]

 

Sent from my iPad using Tapatalk

Link to comment
Share on other sites

Just now, Pip said:


Is that just newer models or something? In my limited tinkering I've opened a few barrels up to have a look, and am currently hunting down a mainspring winder so that I can get the mainspring out and clean and oil them and put them back without knackering them! I know Seiko don't recommend it but for a vintage piece I had kind of gathered that it was part of doing a proper service.

I believe Seiko has been using "sealed for life" barrels since many decades. Beside that is debatable if mainsprings needs to be greased (certainly not oiled), that applies to mov.ts with barrels and mainsprings designed to be opened and replaced. Seiko doesn't fall into this category. You will also have trouble finding a winder that fits well with Seiko mainsprings.

  • Like 1
Link to comment
Share on other sites

I believe Seiko has been using "sealed for life" barrels since many decades. Beside that is debatable if mainsprings needs to be greased (certainly not oiled), that applies to mov.ts with barrels and mainsprings designed to be opened and replaced. Seiko doesn't fall into this category. You will also have trouble finding a winder that fits well with Seiko mainsprings.

Standard thing that I've seen is (and what I'm planning to do):
Open barrel and remove mainspring, clean in some (? Can't recall) in some watchmakers paper and clean barrel and arbor in US. Put a dab of graphite grease on barrel wall. Use Bergeon No.7 (10.8mm I think?) winder, most are RH but some movements are LH and replace ms and arbor in barrel. Put three drops of (?) on top of ms, seal barrel and Bob's your Auntie's live in lover.

I would guess that this is fairly common practice with other movements too?


Sent from my iPad using Tapatalk
Link to comment
Share on other sites

1 minute ago, Pip said:


I would guess that this is fairly common practice with other movements too?

That's the point exactly, what you would do with other movements  is not needed with sealed Seiko barrels, you don't gain anything messing with them. If you are looking to address a real problem and a way to increase amplitude on low ends Seiko look at the non-jeweled barrel bushings (just holes in the plates) which gets ovali with time.

  • Like 1
Link to comment
Share on other sites

1 hour ago, Pip said:

the 7005 is not a new movement so I'm honestly interested to hear what the verdict is

Pip I will let you know, I just think not checking the mainspring is like doing a service on a car and not changing the oil, maybe mark could put us right......

  • Like 2
Link to comment
Share on other sites

If you're not cannot for any reason source a new sealed replacement barrel as recommended by Seiko, open it up, clean it out, replace the mainspring if you can source one, then luricate  and reassemble the barrel.  As alluded to above, I would not refurbish a car engine and run it, with old contaminated oil when it could have been changed.

Link to comment
Share on other sites

17 minutes ago, Geo said:

If you're not cannot for any reason source a new sealed replacement barrel as recommended by Seiko, open it up, clean it out, replace the mainspring if you can source one, then luricate  and reassemble the barrel.  As alluded to above, I would not refurbish a car engine and run it, with old contaminated oil when it could have been changed.

Thanks Geo I thought I was going mad :Bravo:

Link to comment
Share on other sites

36 minutes ago, Geo said:

If you're not cannot for any reason source a new sealed replacement barrel as recommended by Seiko, open it up, clean it out, replace the mainspring if you can source one, then luricate  and reassemble the barrel.

But in 99% of the cases that's not needed with sealed Seiko barrels, and if done with bare hands or even gloves that will just introduce debris into it. I speak from the direct experience of many hours and tries backed up by timegrapher testing. If a entry level Seiko doesn't run good, be reassured it's not the mainspring fault.

Link to comment
Share on other sites

1 hour ago, BUSAKAZ said:

Pip I will let you know, I just think not checking the mainspring is like doing a service on a car and not changing the oil, maybe mark could put us right......

Have a read of this thread Kaz and make up your own mind.

 

Link to comment
Share on other sites

12 minutes ago, rogart63 said:

A barrel with mainspring from the newer 7s26 would work fine if you don't want to take the mainspring out? 

 

Thanks, it looks ok visually I'm going to put it together tomorrow and give it a whirl....

  • Like 1
Link to comment
Share on other sites



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • that band is old as stated, there is a kit that pops up from time to time on selling sites for the repair of these type bands, some of this type are adjustable on a few links, one adjustable type allows you to align the round opening in the expansion slit [like yours] with the rivet to separate, but if yours won't come out then the rivet head is too big and will have to be done with some rivet removal and replacement, I suppose if you could make/optain the correct rivets that one could alter the said band, the tops/caps do lift off after raising the tabs....  
    • This is a watch from a friend who sent it to a neighborhood watchmaker for a battery change. It came back with the watch stem in a ziplock bag and the dial skewed 20°. The watchmaker told him that the stem was faulty and the watch cannot be repaired. I opened up the watch and found that one dial foot was broken off and still stuck in the movement, while the other was bent until it was flat against the dial. The stem could be inserted but it couldn't be pulled out to quickset and time adjusting positions. I did a full disassemble, cleaned and oiled the movement. But when it put in the battery, the second hand runs super fast. Like it gains 30 mins every hour. Any advice on fixing this problem? TIA.
    • I determined that the balance staff is rotating, not the roller table, so my second attempt at riveting was unsuccessful. I have ordered a new balance staff and will take measurements when it arrives. The balance staff i originally ordered (and now reordered) was specified as: Replacement balance staff: (A. Schild Caliber 984 1002 1021 1124 Original Balance Staff Part 723) so it should be correct. Measurements: (see pic below for terminology) xxxyy is a place holder until the new balance staff arrives. Lower pivot: Old - .08 mm New - xxxyy Lower pivot to balance seat: Old - 1.53 mm New - xxxyy Roller shoulder: Old - .42 mm New - xxxyy Hub: Old - xxxyy New - xxxyy Balance shoulder: Old - .86 mm New - xxxyy Collet shoulder: Old - .56 mm New - xxxyy Upper pivot: Old - broken New - xxxyy
    • Hello and welcome from Leeds.  We're here to help. 
    • I was just about to adk that, probably they have unnecessary waiting lists to make their watches appear more exclusive than they actually are.
×
×
  • Create New...