Jump to content

Vintage Rotary

anilv

By anilv
in Your Watch Collection

 Share

Recommended Posts

anilv Distinguished Member

anilv

Posted
Posted

Hi guys,

Wearing an old Rotary today. This is an older watch, probably from the 40s.

The case is Gold-plated and has seen some wear. Under the "Rotary' it says 'Super sports' . Above the sub-seconds dial it says 'shock-absorber' and 'anti-magnetic'. It has fixed lugs which makes swapping strap difficult, the one it has on is meant for fixed lugs and has a sturdy fold-over (probably metal inside) which clips on the lug. It has nice simple hands which have been blued well, the center of the minute hand has been left silver given a niece contrast. The case back is a faithful rendition of the dark side of the moon.

P_20170317_083415.thumb.jpg.5454ef992507d58b9a6cd1b52a2f7748.jpg

Nice hands

P_20170317_084400.thumb.jpg.6f8c1dc64854d6b08ee2cb25c2daf276.jpg

The dark side of the moon... not much can be done here without spending too much money.

P_20170317_085635.thumb.jpg.7d7d061fc4440ec0a958865117e535f0.jpg

The inside of the dark side of the moon.. I believe the '38' means 1938? At any rate, its more than 10 years old ;so good job Meteor!

P_20170317_083454.thumb.jpg.3bf36e5b74803b453b81624859f8b52e.jpg

When you pop off the bac, the movement stays in the caseback. You have to use a bit of force, working around the edges, before it comes away and you are left with this.. an inner caseback. This is comes off easily.

P_20170317_083502.thumb.jpg.adb28693ecb1e3ab6498c8730597e33a.jpg

Revealing the movement. I think it's an FHF of some sort. Note the early form of shock protection on the balance cock .. the cap jewel is retained by a spring plate and will 'give' is subjected to a hard knock. The problem with these early shock absorbers is that they were only mildly effective and that only if it hit the ground level. It had not much lateral movement built-in so if it landed edge-on the pivot would still break. Still better than no shock-absorber I suppose, If I am not mistaken Breguet pioneer this and later on it is common to find a similar system on Cyma watches. The ratchet-wheel has the normal Rotary 'Flying-wheel' which reminds me of a vintage car..Austin I think?  You can see the early type dial holding screws at 6 o'clock and slightly after 12.  The movement is marked 7/440 and just belove that there's a 'V" or maybe the 'pheon'? The watch runs well and keeps time. I haven't done anything to it but the regulator is cranked over to slow so there may be other issues, need to get some case screws too. Not so evident from the pictures is that the plates have been plated with a 'whiter' finish which looks like silver. You see similar on Movado movements. Finally in the era before center seconds, 15 jewels was as good as it got so this would have been made for the higher end of the market.

P_20170317_083514.thumb.jpg.08d3ea73ffe15b44ace0eb87cb606b4a.jpgv

Well its almost the weekend so have a good one!

Anilv

 

  • Like 4
Link to comment
Share on other sites
Geo Distinguished Member

Geo

Posted
Posted

I like this watch Anil, I hope you track down more history.  Although the minute and hour hand look great, I feel one or both may have been fitted somewhere down the line.  The open diamond hands look the business, but I have only seen them fitted in matching pairs.

Regarding the dark side of the moon, I was looking for a triangular prism with bands of light being emitted. :ph34r:

  • Like 1
Link to comment
Share on other sites
oldhippy Distinguished Member

oldhippy

Posted
Posted
19 minutes ago, Geo said:

I like this watch Anil, I hope you track down more history.  Although the minute and hour hand look great, I feel one or both may have been fitted somewhere down the line.  The open diamond hands look the business, but I have only seen them fitted in matching pairs.

Regarding the dark side of the moon, I was looking for a triangular prism with bands of light being emitted. :ph34r:

The hands don't match.

  • Like 1
Link to comment
Share on other sites
Wesley881 Watch Enthusiast

Wesley881

Posted
Posted

Great watch!  I have a new skeleton frame pocket watch from Rotary.  I went into Marshall's to get some long johns for an upcoming Winter hike and maybe some other factory seconds/discounts when I happened upon it.  It had been marked down from "$599" to $50!  I know these stores often inflate these numbers to drive a deal, but WOW.  Anyway, it is a very nice piece and I've enjoyed carrying it from time to time...are puns OK?

  • Like 1
Link to comment
Share on other sites
digginstony Super WRT Addict

digginstony

Posted
Posted

Wow, a Rotary without a Chinese movement in. What a delight. If I'm looking right:- 6 bridges including the pallet fork? What a joy to work on. Absolutely love the watch even with replacement hands, though I would change them anyway as I prefer Batons.

Sent from my SM-T585 using Tapatalk

  • Like 1
Link to comment
Share on other sites
digginstony Super WRT Addict

digginstony

Posted
Posted
I assume the train bridge is actually one part, made to look like 3.
You're going to struggle to claim on that case wear warranty - I suspect it is slightly more than 10 years old!

Yep re looking at the photo the train bridge is probably all one. Though I could of swore I saw seem on the part below the "15 Jewels" could be a shadow.

Sent from my SM-T585 using Tapatalk

Link to comment
Share on other sites
  • 4 years later...
Nucejoe Distinguished Member

Nucejoe

Posted
Posted

 I think they made in- house movements at first or when in switzerland, once head quarters were moved to London, the company  expanded fast so started sourcing movements from others manufacturers, think Longines is now in swatch group. not sure though, but its a good make, never had problem with my watch.

Regs

 

  • Like 1
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Similar Content

  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Hawaiikook808
      Balance spring fell out of regulator pin.

      By Hawaiikook808 · Posted

      Thank you so much, Hector and CJ. I appreciate the tech sheet and the video. Gasp, I think I will make the attempt. What's the worst that can happen? I think there may be a new balance complete in my future, though.  I'll update the post and let you know the result. R, Frank  
    • Waggy
      Movement holder made with 3D printer

      By Waggy · Posted

      So here is the new base (v 2.1), I made it so that the base will fit over and swallow the stump of the hand pusher tool (or at least my clone of the tool), I also reduced the OD of the bottom skirt a little as it looked/felt a little large, here are a few pictures and the fake .pdf file which you need to convert to .zip once downloaded.   The cut-out seen on the below image on the bottom of the base should swallow the OD (40 mm, +0.1 mm tolerance) of the stump and the height of the stump 9.5mm (measured to 9.1mm, but rounded to 9.5mm) - let me know if this works for your tool.   Note, I think you may need to print supports for the new internal shelf created? Here is the fake .pdf for just the FreeCAD base file and 3mf files Modular Movement Holder.pdf Here is the fake pdf for complete set of the new base and ring FreeCAD/3mf files: Modular Movement Holder base and ring v 2.1.pdf However, I'm wondering how often you could use this feature, adding the dial usually increases the OD of the movement, so you would need a new (larger) adapter ring tuned to the OD of the dial and I wouldn't like to grip the dial in any kind of movement holder if It could be avoided for fear of damaging it. Maybe I'm misunderstanding you?
    • HectorLooi
      Balance spring fell out of regulator pin.

      By HectorLooi · Posted

      Hi Frank, you have dived headlong into the deep end. Hairspring work has to be the scariest thing a newbie has to tackle. Your hairspring appears to be bent and just putting it back into the regulator would not allow the balance to work properly. It might start oscillating but the performance would not be good. The proper thing to do is to unstud the hairspring, remove the hairspring from the balance, reinstall the hairspring on the stud carrier, reshape the endcurve and centre the collet to the balance jewel hole. This challenge would either make you or break you. Hope that you will be able to fix your watch. Welcome to the world of watchmaking.  Watch this video. It think it'll give you an idea of the task ahead. From your 1st photo, I think you have a etachron type stud. Let me see if I can find a video on how to remove it from the arm.
    • Curare
      Balance spring fell out of regulator pin.

      By Curare · Posted

      Have read of the Tech Sheet attached on the balance section page 12. It may be bent but until you reposition it back in the regulator pins you'll never know. Cheers CJ 4R35B_4R36A.pdf
    • Hawaiikook808
      Balance spring fell out of regulator pin.

      By Hawaiikook808 · Posted

      Aloha All, My Seiko 4R35B movement stopped working today. Upon closer inspection, it looks like the balance spring came out of the regulator pin. This is my first time working on a balance. Any advice on how to get this spring repositioned (back to normal)? I'm pretty sure that while adjusting the beat error on this movement, I must have turned the stud (I didn't even know they turned), and the spring eventually fell out.  Will the spring go back to even spacing when it's back in the pin, or does it look bent? Thanks, Frank  
×
×
  • Create New...